| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
EVAL-ADT7470EBZ bảng dữ liệu(PDF) 21 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
EVAL-ADT7470EBZ bảng dữ liệu(HTML) 21 Page - Analog Devices |
|
21 / 40 page ![]() Data Sheet ADT7470 Rev. E | Page 21 of 40 Figure 19 shows a fan drive circuit using an NPN transistor such as a general-purpose MMBT2222. While these devices are inexpensive, they tend to have much lower current handling capabilities and higher on resistance than MOSFETs. When choosing a transistor, care should be taken to ensure that it meets the fan’s current requirements. This is the only major difference between a MOSFET and NPN transistor fan driver circuit. When using transistors, ensure that the base resistor is chosen such that the transistor is fully saturated when the fan is powered on. Otherwise, there are power inefficiencies in the implementation. 12V Q1 MMBT2222 PWM 3.3V 470 Ω 12V FAN TACH/AIN ADT7470 12V 10k Ω TACH 10k Ω 4.7k Ω 1N4148 Figure 19. Driving a 3-Wire Fan Using an NPN Transistor Low Frequency SETTING THE FAN DRIVE FREQUENCY Configuration Register 2 Bits[6:4] configure the fan drive frequency in both high and low frequency drive mode. Table 16. Fan Drive Frequency Register 0x74[6:4] High Frequency Drive (0x40[6] = 0) Low Frequency Drive (0x40[6] = 1) 000 1.4 kHz 11 Hz 001 22.5 kHz 14.7 Hz 010 22.5 kHz 22.1 Hz 011 22.5 kHz 29.4 Hz 100 22.5 kHz 35.3 Hz 101 22.5 kHz 44.1 Hz 110 22.5 kHz 58.8 Hz 111 22.5 kHz 88.2 Hz INVERTED PWM OUTPUT The PWM duty cycle can be inverted by writing to the PWM Configuration registers. If the PWM duty cycle is inverted, then a PWM duty cycle setting of 33% results in an output duty cycle of 66%, as the PWM waveform is inverted. Table 17. PWM1/PWM2 Configuration (Register 0x68) Bit No. Mnemonic Description 5 INV1 0 = PWM1 duty cycle not inverted (default). 1 = PWM1 duty cycle inverted. 4 INV2 0 = PWM2 duty cycle not inverted (default). 1 = PWM2 duty cycle inverted. Table 18. PWM3/PWM4 Configuration (Register 0x69) Bit No. Mnemonic Description 5 INV3 0 = PWM3 duty cycle not inverted (default). 1 = PWM3 duty cycle inverted. 4 INV4 0 = PWM4 duty cycle not inverted (default). 1 = PWM4 duty cycle inverted. FAN FULL SPEED FUNCTION When Pin 13 is configured for full speed operation, pulling the pin low will cause all fans to run at the maximum PWM duty cycle. A Logic 1 is output on the PWM pins in this case. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |