công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

EVAL-ADT7470EBZ bảng dữ liệu(PDF) 7 Page - Analog Devices

tên linh kiện EVAL-ADT7470EBZ
Giải thích chi tiết về linh kiện  Temperature Sensor Hub and Fan Controller
PDF  40 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  AD [Analog Devices]
Trang chủ  http://www.analog.com
Logo AD - Analog Devices

EVAL-ADT7470EBZ bảng dữ liệu(HTML) 7 Page - Analog Devices

Back Button EVAL-ADT7470EBZ Datasheet HTML 3Page - Analog Devices EVAL-ADT7470EBZ Datasheet HTML 4Page - Analog Devices EVAL-ADT7470EBZ Datasheet HTML 5Page - Analog Devices EVAL-ADT7470EBZ Datasheet HTML 6Page - Analog Devices EVAL-ADT7470EBZ Datasheet HTML 7Page - Analog Devices EVAL-ADT7470EBZ Datasheet HTML 8Page - Analog Devices EVAL-ADT7470EBZ Datasheet HTML 9Page - Analog Devices EVAL-ADT7470EBZ Datasheet HTML 10Page - Analog Devices EVAL-ADT7470EBZ Datasheet HTML 11Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 7 / 40 page
background image
Data Sheet
ADT7470
Rev. E | Page 7 of 40
FUNCTIONAL DESCRIPTION
GENERAL DESCRIPTION
The ADT7470 is a multichannel, pulse-width modulation
(PWM) fan controller and monitor for any system requiring
monitoring and cooling. The device communicates with the
system via a serial system management bus. The device has
a single address line for address selection (Pin 11), a serial
data line for reading and writing addresses and data (Pin 16),
and an input line for the serial clock (Pin 1). All control and
programming functions of the ADT7470 are performed over
the serial bus, which supports both SMBus and fast I2C speci-
fications. In addition, an SMBALERT interrupt output is
provided to indicate out-of-limit conditions.
When the ADT7470 monitoring sequence is started, it cycles
through each fan tach input to measure fan speed. Measured
values from these inputs are stored in value registers. These
can be read out over the serial bus, or they can be automatically
compared with programmed limits stored in the limit registers.
The results of out-of-limit comparisons are stored in the status
registers, which can be read over the serial bus to flag out-of-
limit conditions. If fan speeds drop below preset levels or a
fan stalls, an interrupt is generated. Likewise, the ADT7470
can flag fan over speed conditions by using limits set in the
fan tach maximum registers.
ADT7470 Monitoring Cycle
The monitoring cycle begins when a 1 is written to the start
bit (Bit 0) of Configuration Register 1 (Register 0x40). Each
fan tach input is monitored in turn, and, as each measurement
is completed, the result is automatically stored in the appropri-
ate value register. Multiple temperature channels can also be
monitored by clocking in temperatures using the TMP_IN
pin. The temperature measurement function is addressed
in hardware and requires no software intervention. The
monitoring cycle continues unless disabled by writing a 0
to Bit 7 of Configuration Register 1.
The rate of temperature measurement updates depends on
the nominal conversion rate of the TMP05/TMP06 temperature
sensor (approximately 120 ms) and on the number of TMP05s
daisy-chained together. The total monitoring cycle time is the
temperature conversion time multiplied by the number of
temperature channels being monitored.
Fan tach measurements are taken in parallel and are not syn-
chronized with the temperature measurements in any way
CONFIGURATION REGISTER 1 (ADDRESS 0X40)
This register contains the STRT bit, Bit 0, which begins the
monitoring cycle on the ADT7470.
The SMBus timeout can be disabled , fast tach enabled, and
the registers locked, by writing to this register.
Control of high or low frequency fan drive, and the config-
uration for Pin 13, can be accessed via this register.
See Table 31 for more details.
CONFIGURATION REGISTER 2 (ADDRESS 0X74)
Writing a 1 to Bit 0 in this register puts the ADT7470 in
shutdown mode, which puts the part into a low current
consumption mode.
The PWM frequency for each fan is controlled via this register.
Fan speed measurement can be disabled for each fan by writing
to this register.
See Table 44 for more details.
ID REGISTERS
The ADT7470 has three read-only registers for identifying
the part and silicon revision.
The device ID register is located at address 0x3D, and is set
to 0x70.
The company ID register, located at address 0x3E, is set to 0x41.
The revision number register is at address 0x3F, and contains
the revision number of the ADT7470 silicon.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com