TMS320DM355 datasheet(83/163 Pages) TI1

83 / 163 page

TMS320DM355

www.ti.com

SPRS463G – SEPTEMBER 2007 – REVISED JUNE 2010

•

Power management

–

Deep sleep mode

•

Bandwidth Management

–

Bus master DMA priority control

For more information on the System Control Module refer to TMS320DM35x Digital Media

System-on-Chip (DMSoC) ARM Subsystem Reference Guide (literature number SPRUFB3) .

3.9

Pin Multiplexing

The DM355 makes extensive use of pin multiplexing to accommodate the large number of peripheral

functions in the smallest possible package. In order to accomplish this, pin multiplexing is controlled using

a combination of hardware configuration (at device reset) and software control. No attempt is made by the

DM355 hardware to ensure that the proper pin muxing has been selected for the peripherals or interface

mode being used, thus proper pin muxing configuration is the responsibility of the board and software

designers. An overview of the pin multiplexing is shown in Table 3-18.

Table 3-18. Peripheral Pin Mux Overview

Peripheral

Muxed With

Primary Function

Secondary Function

Tertiary Function

VPFE (video in)

GPIO and SPI2

VPFE (video in)

SPI2

GPIO

VPBE (video out)

GPIO, PWM, and RTO

VPBE (video out)

PWM and RTO

GPIO

AEMIF

GPIO

AEMIF

GPIO

none

ASP0

GPIO

ASP0

GPIO

none

MMC/SD1

GPIO and UART2

MMC/SD1

GPIO

UART2

CLKOUT

GPIO

CLKOUT

GPIO

none

I2C

GPIO

I2C

GPIO

none

UART1

GPIO

UART1

GPIO

none

SPI1

GPIO

SPI1

GPIO

none

SPI0

GPIO

SPI0

GPIO

none

3.9.1

Hardware Controlled Pin Multiplexing

Use the Asynchronous EMIF configuration pins (AECFG[3:0]) for hardware pin mux control. AECFG[3:0]

control the partitioning of the AEMIF addresses and GPIOs at reset, which allows you to properly

configure the number of AEMIF address pins required by the boot device while unused addresses pins are

available as GPIOs. These settings may be changed by software after reset by programming the PinMux2

address bits enabled on the AEMIF is selectable from 0 to 16. Pins that are not assigned to another

peripheral and not enabled as address signals become GPIOs (except EM_A[2:1]). The enabled address

signals are always contiguous from EM_BA[1] upwards; bits cannot be skipped. The exception to this are

EM_A[2:1]. These signals (can be used to) represent the ALE and CLE signals for the NAND Flash mode

of the AEMIF and are always enabled. Note that EM_A[0] does not represent the lowest AEMIF address

bit. DM355 supports only 16-bit and 8-bit data widths for the AEMIF. In 16-bit mode, EM_BA[1] represents

the LS address bit (the half-word address) and EM_BA[0] represents the MS address bit (A[14]). In 8-bit

mode, EM_BA[1:0] represent the 2 LS address bits. Note that additional selections are available by

programming the PinMux2 register in software after boot. Note that AECFG selection of ‘0010’ selects

OneNAND interface. The AEMIF needs to operate in the half-rate mode (full_rate = 0) to meet frequency

requirements. Software should not change the PINMUX2 register setting to affect the AEMIF rate

operation. A soft reset of the AEMIF should be performed any time a rate change is made.

Detailed Device Description

Submit Documentation Feedback

Product Folder Link(s): TMS320DM355

TMS320DM355 bảng dữ liệu(PDF) 83 Page - Texas Instruments

TMS320DM355 bảng dữ liệu(HTML) 83 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL