COP8CCR9IMT7SLASHNOPB datasheet(11/111 Pages) TI1

11 / 111 page

COP8CBR9, COP8CCR9, COP8CDR9

www.ti.com

SNOS535I – OCTOBER 2000 – REVISED MARCH 2013

Electrical Specifications

3.1

Absolute Maximum Ratings

(1) (2)

Supply Voltage (VCC)

Voltage at Any Pin

−0.3V to VCC +0.3V

Total Current into VCC Pin (Source)

200 mA

Total Current out of GND Pin (Sink)

200 mA

Storage Temperature Range

−65°C to +140°C

ESD Protection Level

2 kV (Human Body Model)

(1)

Absolute maximum ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications are not

ensured when operating the device at absolute maximum ratings.

(2)

If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.

3.2

Electrical Characteristics DC Electrical Characteristics (

−40°C ≤ T

A ≤ +85°C)

Datasheet min/max specification limits are ensured by design, test, or statistical analysis.

Parameter

Conditions

Min

Typ

Max

Units

Operating Voltage

2.7

5.5

Power Supply Rise Time

50 x 106

Power Supply Ripple(1)

Peak-to-Peak

0.1 VCC

Supply Current(2)

High Speed Mode

CKI = 10 MHz

VCC = 5.5V, tC = 0.5 μs

13.2

CKI = 3.33 MHz

VCC = 4.5V, tC = 1.5 μs

Dual Clock Mode

CKI = 10 MHz, Low Speed OSC = 32 kHz

VCC = 5.5V, tC = 0.5 μs

13.2

CKI = 3.33 MHz, Low Speed OSC = 32 kHz

VCC = 4.5V, tC = 1.5 μs

Low Speed Mode

Low Speed OSC = 32 kHz

VCC = 5.5V

103

μA

HALT Current with BOR Disabled(3)

High Speed Mode

VCC = 5.5V, CKI = 0 MHz

μA

Dual Clock Mode

VCC = 5.5V, CKI = 0 MHz, Low

μA

Speed OSC = 32 kHz

Low Speed Mode

VCC = 5.5V, CKI = 0 MHz, Low

μA

Speed OSC = 32 kHz

Idle Current(2)

High Speed Mode

CKI = 10 MHz

VCC = 5.5V, tC = 0.5 μs

2.5

CKI = 3.33 MHz

VCC = 4.5V, tC = 1.5 μs

1.2

Dual Clock Mode

CKI = 10 MHz, Low Speed OSC = 32 kHz

VCC = 5.5V, tC = 0.5 μs

2.5

CKI = 3.33 MHz, Low Speed OSC = 32 kHz

VCC = 4.5V, tC = 1.5 μs

1.2

Low Speed Mode

Low Speed OSC = 32 kHz

VCC = 5.5V

μA

(1)

Maximum rate of voltage change must be < 0.5 V/ms.

(2)

Supply and IDLE currents are measured with CKI driven with a square wave Oscillator, CKO driven 180° out of phase with CKI, inputs

connected to VCC and outputs driven low but not connected to a load.

(3)

The HALT mode will stop CKI from oscillating. Measurement of IDD HALT is done with device neither sourcing nor sinking current; with

L. A. B, C, E, F, G0, and G2–G5 programmed as low outputs and not driving a load; all D outputs programmed low and not driving a

load; all inputs tied to VCC; A/D converter and clock monitor and BOR disabled. Parameter refers to HALT mode entered via setting bit 7

of the G Port data register.

Electrical Specifications

Submit Documentation Feedback

Product Folder Links: COP8CBR9 COP8CCR9 COP8CDR9

COP8CCR9IMT7/NOPB bảng dữ liệu(PDF) 11 Page - Texas Instruments

COP8CCR9IMT7/NOPB bảng dữ liệu(HTML) 11 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL