DM330023-2 datasheet(43/64 Pages) MICROCHIP

43 / 64 page

Hardware

 2009 Microchip Technology Inc.

DS70605A-page 37

4.2.2

Power Supplies

The system default configuration is to get the 15V, 3.3V and 3.3V analog rail voltages

from the PFC stage board. However, it is also possible to use an external 24V power

supply to generate these voltages.

U19, C70, C73, C71 and C74 regulate the voltage applied to the system via J15 (28V

max). The output of the regulator is connected to the system through R109. The circuit

is shown in Appendix A. “Board Layout and Schematics”.

U18, C67, R110, C68, D16, D15, L3, R111, R112 and C75 regulate the 15 volts to cre-

ate a 3.3V digital rail. This auxiliary 3.3V digital rail is applied to the system through

R106. The circuit is shown in Appendix A. “Board Layout and Schematics”.

R114, R107, C69, and C72 form a decoupling circuit for generating a 3.3V rail for the

analog circuitry such as the ADC reference and the current feedback reference. This

auxiliary 3.3V analog rail is applied to the system through R108.

4.2.3

Power Module

The three-phase inverter is embedded in a power module (U16). This power module

contains:

• 600V/30A 3-phase IGBT Inverter Bridge

• Gate driver circuitry for each IGBT

• Three Independent connections to the negative DC bus for current sensing

• Short-circuit protection circuitry

• Thermal Shutdown

• Gate Driver Power Supply Undervoltage protection

• Gate Driver Power Supply Overvoltage protection

• Single-grounded power supply

• Isolation of 2.5 kV per minute

• Maximum switching frequency: 20 kHz

The dsPIC DSC provides the PWM signals to this power module in order to turn on/off

the IGBT, and therefore apply power to the motor phases.

R95 sets the threshold limit for the overcurrent circuitry. If this voltage is greater than

0.5 V (typical), a fault signal is asserted and the low-side IGTBs are turned off. R94 and

C53 form a low-pass RC filter that filters out the frequencies above 88.4 kHz.

C56 sets the fault pulse duration, the value of C56 is given by the following equation:

C56 = 18.3E-6 x 1.8E-3 seconds. Therefore, the fault pulse duration is 54 µs

The power module fault output pin (VFO) is open-collector configured. R50 pulls up the

fault output to the analog 3.3V rail. R53 and C40 form a low-pass RC filter that filters

out the frequencies above 53 kHz.

For more information about this power module please refer to the manufacturer’s data

sheet.

Note: It is the responsibility of the user to populate these components if an

external power supply is used.

Note: It is the responsibility of the user to populate these components if an

external power supply is used.

Note: It is the responsibility of the user to populate these components if an

external power supply is used.

DM330023-2 bảng dữ liệu(PDF) 43 Page - Microchip Technology

DM330023-2 bảng dữ liệu(HTML) 43 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

bảng dữ liệu tải về

Link URL