| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LPC810M021FN8 bảng dữ liệu(PDF) 79 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
LPC810M021FN8 bảng dữ liệu(HTML) 79 Page - NXP Semiconductors |
|
79 / 313 page ![]() UM10601 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2012. All rights reserved. Preliminary user manual Rev. 1.0 — 7 November 2012 79 of 313 NXP Semiconductors UM10601 Chapter 7: LPC800 GPIO port 7.6.6 GPIO masked port pin registers These registers are similar to the PIN registers, except that the value read is masked by ANDing with the inverted contents of the corresponding MASK register, and writing to one of these registers only affects output register bits that are enabled by zeros in the corresponding MASK register 7.6.7 GPIO port set registers Output bits can be set by writing ones to these registers, regardless of MASK registers. Reading from these register returns the port’s output bits, regardless of pin directions. 7.6.8 GPIO port clear registers Output bits can be cleared by writing ones to these write-only registers, regardless of MASK registers. Table 73. GPIO port 0 pin register (PIN0, address 0xA000 2100) bit description Bit Symbol Description Reset value Access 17:0 PORT0 Reads pin states or loads output bits (bit 0 = PIO0_0, bit 1 = PIO0_1, ..., bit 17 = PIO0_17). 0 = Read: pin is low; write: clear output bit. 1 = Read: pin is high; write: set output bit. ext R/W 31:18 - Reserved. 0 - Table 74. GPIO masked port 0 pin register (MPIN0, address 0xA000 2180) bit description Bit Symbol Description Reset value Access 17:0 MPORTP0 Masked port register (bit 0 = PIO0_0, bit 1 = PIO0_1, ..., bit 17 = PIO0_17). 0 = Read: pin is LOW and/or the corresponding bit in the MASK register is 1; write: clear output bit if the corresponding bit in the MASK register is 0. 1 = Read: pin is HIGH and the corresponding bit in the MASK register is 0; write: set output bit if the corresponding bit in the MASK register is 0. ext R/W 31:18 - Reserved. 0 - Table 75. GPIO set port 0 register (SET0, address 0xA000 2200) bit description Bit Symbol Description Reset value Access 17:0 SETP0 Read or set output bits. 0 = Read: output bit: write: no operation. 1 = Read: output bit; write: set output bit. 0R/W 31:18 - Reserved. 0 - |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |