| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
AM1707ZKB4 bảng dữ liệu(PDF) 105 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
AM1707ZKB4 bảng dữ liệu(HTML) 105 Page - Texas Instruments |
|
105 / 155 page ![]() AM1705 www.ti.com SPRS657A – FEBRUARY 2010 – REVISED APRIL 2010 Table 6-61. Additional (1) SPI1 Master Timings, 5-Pin Option (2) (3) (continued) No. PARAMETER MIN MAX UNIT Max delay for slave SPI to drive SPI1_ENA 21 td(SCSL_ENAL)M valid after master asserts SPI1_SCS to delay C2TDELAY + P ns the master from beginning the next transfer. Polarity = 0, Phase = 0, 2P -5 to SPI1_CLK rising Polarity = 0, Phase = 1, Delay from 0.5tc(SPC)M + 2P -5 to SPI1_CLK rising SPI1_SCS active to 22 td(SCS_SPC)M ns first SPI1_CLK(7) (8) Polarity = 1, Phase = 0, 2P -5 (9) to SPI1_CLK falling Polarity = 1, Phase = 1, 0.5tc(SPC)M + 2P -5 to SPI1_CLK falling Polarity = 0, Phase = 0, 3P + 3 to SPI1_CLK rising Polarity = 0, Phase = 1, Delay from assertion 0.5tc(SPC)M + 3P + 3 to SPI1_CLK rising of SPI1_ENA low to 23 td(ENA_SPC)M ns first SPI1_CLK Polarity = 1, Phase = 0, 3P + 3 edge.(10) to SPI1_CLK falling Polarity = 1, Phase = 1, 0.5tc(SPC)M + 3P + 3 to SPI1_CLK falling (7) If SPI1_ENA is asserted immediately such that the transmission is not delayed by SPI1_ENA. (8) In the case where the master SPI is ready with new data before SPI1_SCS assertion. (9) This delay can be increased under software control by the register bit field SPIDELAY.C2TDELAY[4:0]. (10) If SPI1_ENA was initially deasserted high and SPI1_CLK is delayed. Table 6-62. Additional(1) SPI1 Slave Timings, 4-Pin Enable Option(2) (3) No. PARAMETER MIN MAX UNIT Polarity = 0, Phase = 0, 1.5 P -3 2.5 P + 19 from SPI1_CLK falling Delay from Polarity = 0, Phase = 1, final – 0.5tc(SPC)M + 1.5 P -3 – 0.5tc(SPC)M + 2.5 P + 19 from SPI1_CLK falling SPI1_CLK 24 td(SPC_ENAH)S ns edge to slave Polarity = 1, Phase = 0, 1.5 P -3 2.5 P + 19 deasserting from SPI1_CLK rising SPI1_ENA. Polarity = 1, Phase = 1, – 0.5tc(SPC)M + 1.5 P -3 – 0.5tc(SPC)M + 2.5 P + 19 from SPI1_CLK rising (1) These parameters are in addition to the general timings for SPI slave modes ( Table 6-58 ). (2) P = SYSCLK2 period (3) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four slave clocking modes. Table 6-63. Additional(1) SPI1 Slave Timings, 4-Pin Chip Select Option(2) (3) No. PARAMETER MIN MAX UNIT Required delay from SPI1_SCS asserted at slave to first 25 td(SCSL_SPC)S P ns SPI1_CLK edge at slave. Polarity = 0, Phase = 0, 0.5tc(SPC)M + P + 5 from SPI1_CLK falling Polarity = 0, Phase = 1, P + 5 Required delay from final from SPI1_CLK falling 26 td(SPC_SCSH)S SPI1_CLK edge before ns Polarity = 1, Phase = 0, SPI1_SCS is deasserted. 0.5tc(SPC)M + P + 5 from SPI1_CLK rising Polarity = 1, Phase = 1, P + 5 from SPI1_CLK rising Delay from master asserting SPI1_SCS to slave driving 27 tena(SCSL_SOMI)S P + 19 ns SPI1_SOMI valid (1) These parameters are in addition to the general timings for SPI slave modes ( Table 6-58 ). (2) P = SYSCLK2 period (3) Figure shows only Polarity = 0, Phase = 0 as an example. Table gives parameters for all four slave clocking modes. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications 105 Submit Documentation Feedback Product Folder Link(s): AM1705 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |