| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
AM1707ZKB4 bảng dữ liệu(PDF) 102 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
AM1707ZKB4 bảng dữ liệu(HTML) 102 Page - Texas Instruments |
|
102 / 155 page ![]() AM1705 SPRS657A – FEBRUARY 2010 – REVISED APRIL 2010 www.ti.com Table 6-57. General Timing Requirements for SPI1 Master Modes (1) (continued) No. PARAMETER MIN MAX UNIT Polarity = 0, Phase = 0, 0.5tc(SPC)M -3 from SPI1_CLK falling Polarity = 0, Phase = 1, 0.5tc(SPC)M -3 Output hold time, SPI1_SIMO from SPI1_CLK rising 6 toh(SPC_SIMO)M valid after ns Polarity = 1, Phase = 0, receive edge of SPI1_CLK 0.5tc(SPC)M -3 from SPI1_CLK rising Polarity = 1, Phase = 1, 0.5tc(SPC)M -3 from SPI1_CLK falling Polarity = 0, Phase = 0, 0 to SPI1_CLK falling Polarity = 0, Phase = 1, 0 Input Setup Time, to SPI1_CLK rising 7 tsu(SOMI_SPC)M SPI1_SOMI valid before ns Polarity = 1, Phase = 0, receive edge of SPI1_CLK 0 to SPI1_CLK rising Polarity = 1, Phase = 1, 0 to SPI1_CLK falling Polarity = 0, Phase = 0, 5 from SPI1_CLK falling Polarity = 0, Phase = 1, 5 Input Hold Time, SPI1_SOMI from SPI1_CLK rising 8 tih(SPC_SOMI)M valid after receive edge of ns Polarity = 1, Phase = 0, SPI1_CLK 5 from SPI1_CLK rising Polarity = 1, Phase = 1, 5 from SPI1_CLK falling Table 6-58. General Timing Requirements for SPI1 Slave Modes(1) No. PARAMETER MIN MAX UNIT 9 tc(SPC)S Cycle Time, SPI1_CLK, All Slave Modes greater of 2P or 20 ns 256P ns 10 tw(SPCH)S Pulse Width High, SPI1_CLK, All Slave Modes 18 ns 11 tw(SPCL)S Pulse Width Low, SPI1_CLK, All Slave Modes 18 ns Polarity = 0, Phase = 0, 2P to SPI1_CLK rising Polarity = 0, Phase = 1, Setup time, transmit data 2P to SPI1_CLK rising written to SPI before initial 12 tsu(SOMI_SPC)S ns clock edge from Polarity = 1, Phase = 0, 2P master.(2) (3) to SPI1_CLK falling Polarity = 1, Phase = 1, 2P to SPI1_CLK falling Polarity = 0, Phase = 0, 19 from SPI1_CLK rising Polarity = 0, Phase = 1, 19 Delay, subsequent bits valid from SPI1_CLK falling 13 td(SPC_SOMI)S on SPI1_SOMI after transmit ns Polarity = 1, Phase = 0, edge of SPI1_CLK 19 from SPI1_CLK falling Polarity = 1, Phase = 1, 19 from SPI1_CLK rising (1) P = SYSCLK2 period (2) First bit may be MSB or LSB depending upon SPI configuration. SO(0) refers to first bit and SO(n) refers to last bit output on SPI1_SOMI. SI(0) refers to the first bit input and SI(n) refers to the last bit input on SPI1_SIMO. (3) Measured from the termination of the write of new data to the SPI module, In analyzing throughput requirements, additional internal bus cycles must be accounted for to allow data to be written to the SPI module by the CPU. 102 Peripheral Information and Electrical Specifications Copyright © 2010, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): AM1705 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |