| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
AM1707ZKB4 bảng dữ liệu(PDF) 37 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
AM1707ZKB4 bảng dữ liệu(HTML) 37 Page - Texas Instruments |
|
37 / 155 page ![]() AM1705 www.ti.com SPRS657A – FEBRUARY 2010 – REVISED APRIL 2010 6.3 Power Supplies 6.3.1 Power-on Sequence The device should be powered-on in the following order: • 2a) CVDD core logic supply • 2b) Other 1.2V logic supplies (RVDD, PLL0_VDDA). Groups 2a) and 2b) may be powered up together or 2a) first followed by 2b). • 3) All 1.8V IO supplies (USB0_VDDA18). • 4) All digital IO and analog 3.3V PHY supplies (DVDD, USB0_VDDA33). USB0_VDDA33 is not required if USB0 is not used and may be left unconnected. There is no specific required voltage ramp rate for any of the supplies. RESET must be maintained active until all power supplies have reached their nominal values. Note: Future devices may support higher performance at a higher core logic voltage (CVDD). If future migration is desired, the current design should provide separate supplies for 2a) and 2b). If not, then 2a) and 2b) may be provided by a single supply. 6.3.2 Power-off Sequence The power supplies can be powered-off in any order as long as the 3.3V supplies do not remain powered with the other supplies unpowered. 6.4 Unused USB0 (USB2.0) Pin Configurations Table 6-1. Unused USB0 Pin Configurations SIGNAL NAME Configuration (When USB0 is not used) USB0_DM No connect USB0_DP No connect USB0_VDDA33 No connect USB0_VDDA18 No connect USB0_VBUS No connect USB0_VDDA12 No connect AHCLKX0/AHCLKX2/USB_REFCLKIN/ No connect or use as alternate function GP2[11] 6.5 Reset 6.5.1 Power-On Reset (POR) A power-on reset (POR) is required to place the device in a known good state after power-up. Power-On Reset is initiated by bringing RESET and TRST low at the same time. POR sets all of the device internal logic to its default state. All pins are 3-stated . While both TRST and RESET need to be asserted upon power up, only RESET needs to be released for the device to boot properly. TRST may be asserted indefinitely for normal operation, keeping the JTAG port interface and device's emulation logic in the reset state. TRST only needs to be released when it is necessary to use a JTAG controller to debug the device or exercise the device's boundary scan functionality. Note: TRST is synchronous and must be clocked by TCK; otherwise, the boundary scan logic may not respond as expected after TRST is asserted. Copyright © 2010, Texas Instruments Incorporated Peripheral Information and Electrical Specifications 37 Submit Documentation Feedback Product Folder Link(s): AM1705 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |