7643 datasheet(16/424 Pages) RENESAS

16 / 424 page

Rev.2.00

Aug 28, 2006

page 12 of 12

7643 Group

REJ09B0133-0200

List of tables

CHAPTER 1 HARDWARE

Table 1 Pin description (1) ............................................................................................................ 5

Table 2 Pin description (2) ............................................................................................................ 6

Table 3 Support products ............................................................................................................... 8

Table 4 Push and pop instructions of accumulator or processor status register ................ 10

Table 5 Set and clear instructions of each bit of processor status register ........................ 11

Table 6 List of I/O port function .................................................................................................. 16

Table 7 Interrupt vector addresses and priority ........................................................................ 22

Table 8 Port functions in memory expansion mode and microprocessor mode .................... 65

Table 9 Summary of M37643F8 (flash memory version) ........................................................ 71

Table 10 List of software commands (CPU rewrite mode) ..................................................... 76

Table 11 Definition of each bit in status register (SRD) ......................................................... 78

Table 12 Description of pin function (Standard Serial I/O Mode) .......................................... 84

Table 13 Software commands (Standard serial I/O mode) ..................................................... 87

Table 14 Definition of each bit of status register (SRD) ......................................................... 94

Table 15 Bits of which state might be changed owing to software write ............................. 99

CHAPTER 2 APPLICATION

Table 2.1.1 Termination of unused pins ........................................................................................ 9

Table 2.4.1 Setting examples of baud rate generator values and transfer bit rate values (f = 12 MHz)

........................................................................................................................................................... 46

Table 2.4.3 Error flags set condition and how to clear error flags ......................................... 48

Table 2.5.1 Address directions and examples of transfer result (1) ....................................... 86

Table 2.5.2 Address directions and examples of transfer result (2) ....................................... 87

Table 2.5.3 Priority to use bus ..................................................................................................... 88

Table 2.6.1 USB PID list ................................................................................................................ 98

Table 2.6.2 IN FIFO States ......................................................................................................... 125

Table 2.6.3 Bits of which state might be changed owing to software write ....................... 166

Table 2.10.2 State in Wait mode ................................................................................................ 194

CHAPTER 3 APPENDIX

Table 3.1.1 Absolute maximum ratings ........................................................................................ 2

Table 3.1.2 Recommended operating conditions ........................................................................ 3

Table 3.1.3 Electrical characteristics (1) ...................................................................................... 4

Table 3.1.4 Electrical characteristics (2) ...................................................................................... 5

Table 3.1.5 Timing requirements ................................................................................................... 6

Table 3.1.6

Timing requirements and switching characteristics in memory expansion and

microprocessor modes ............................................................................................... 7

Table 3.1.7 Recommended operating conditions ........................................................................ 8

Table 3.1.8 Electrical characteristics (1) ...................................................................................... 9

Table 3.1.9 Electrical characteristics (2) .................................................................................... 10

Table 3.1.10 Timing requirements ............................................................................................... 11

Table 3.1.11

Timing requirements and switching characteristics in memory expansion and

microprocessor modes ............................................................................................. 12

Table 3.3.1 Bits of which state might be changed owing to software write ......................... 30

List of tables

7643 bảng dữ liệu(PDF) 16 Page - Renesas Technology Corp

7643 bảng dữ liệu(HTML) 16 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL