| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/20223 bảng dữ liệu(PDF) 456 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/20223 bảng dữ liệu(HTML) 456 Page - Renesas Technology Corp |
|
456 / 992 page ![]() Section 14 Timer RB Rev. 1.00 Oct. 03, 2008 Page 430 of 962 REJ09B0465-0100 14.3.4 Programmable Wait One-Shot Generation Mode This mode outputs one-shot pulses from the TRBO pin after a fixed amount of time based on either program or external trigger input. When a trigger is generated, beginning with that point in time, pulses are output only once for any length of time set in TRBSC, after any length of time set in TRBPR. (1) Starting and Stopping Operation The counting is started when 1 is written to the TOSST bit in TRBOCR or a valid trigger signal is input to the TRGB pin after the TSTART bit in TRBCR is set to 1 and the TCSTF flag is set to 1. For a trigger input, the pulse must be longer than one cycle of the clock source for counting. The counting is stopped when reloading is performed with an underflow of the timer RB counter during the secondary period counting , when 1 is written to the TOSSP bit in TRBOCR, or when 0 is written to the TSTART bit in TRBMR. (2) Forced Termination of Operation Writing 1 to the TSTOP bit in TRBCR stops the counting forcedly. When the counting is forcedly stopped, the timer RB counter, the prescaler counter, and any associated flags are initialized. (3) Interrupt Request An interrupt request is generated on the underflow of the timer RB counter during the secondary period counting. (4) Reading and Writing Count Value Reading TRBPRE and TRBTR reads count values from each register. If a write is performed to TRBPRE, TRBPR, or TRBSC when counting is stopped, set values are written to both the reload register and the counter. If a write is performed to TRBPRE, TRBPR, or TRBSC during counting, data is written only to the respective reload registers. The value written to TRBPRE takes effect in synchronization with the underflow of the prescaler. The value written to TRBPR takes effect during the next one-shot pulse. After writing to TRBSC and TRBPR when TCSTF = 1 or TOSSTF = 0, if a write is successively performed to TRBSC and then to TRBPR, allow an interval of 5 cycles of the clock source for counting before writing 1 to the TOSST bit. In this mode, TRBPRE or TRBPR should not be set to H'00. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |