| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LM5064PMH/NOPB bảng dữ liệu(PDF) 42 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
LM5064PMH/NOPB bảng dữ liệu(HTML) 42 Page - Texas Instruments |
|
42 / 64 page ![]() LM5064 SNVS718E – JUNE 2011 – REVISED FEBRUARY 2013 www.ti.com MFR_SPECIFIC_08: ALERT_MASK (D8h) The ALERT_MASK command is used to mask the SMBA when a specific fault or warning has occurred. Each bit corresponds to one of the 14 different analog and digital faults or warnings that would normally result in an SMBA being asserted. When the corresponding bit is high, that condition will not cause the SMBA to be asserted. If that condition occurs, the registers where that condition is captured will still be updated (STATUS registers, DIAGNOSTIC_WORD) and the external MOSFET gate control will still be active (VIN_OV_FAULT, VIN_UV_FAULT, IIN/PFET_FAULT, CB_FAULT, OT_FAULT). This register is accessed with the PMBus Read / Write Word protocol. The VIN UNDERVOLTAGE FAULT flag will default to 1 on startup, however, it will be cleared to 0 after the first time the input voltage increases above the resistor-programmed UVLO threshold. Table 29. ALERT_MASK Definitions BIT NAME DEFAULT 15 VOUT UNDERVOLTAGE WARN 0 14 IIN LIMIT WARN 0 13 VIN UNDERVOLTAGE WARN 0 12 VIN OVERVOLTAGE WARN 0 11 POWER GOOD 1 10 OVERTEMP WARN 0 9 Not Used 0 8 OVERPOWER LIMIT WARN 0 7 Not Used 0 6 EXT_MOSFET_SHORTED 0 5 VIN UNDERVOLTAGE FAULT 1 4 VIN OVERVOLTAGE FAULT 0 3 IIN/PFET FAULT 0 2 OVERTEMPERATURE FAULT 0 1 CML FAULT (Communications Fault) 0 0 CIRCUIT BREAKER FAULT 0 MFR_SPECIFIC_09: DEVICE_SETUP (D9h) The DEVICE_SETUP command may be used to override pin settings to define operation of the LM5064 under host control. This command is accessed with the PMBus read / write byte protocol. Table 30. DEVICE_SETUP Byte Format Bit Name Meaning 7:5 Retry setting 111 = Unlimited retries 110 = Retry 16 times 101 = Retry 8 times 100 = Retry 4 times 011 = Retry 2 times 010 = Retry 1 time 001 = No retries 000 = Pin configured retries 4 Current limit setting 0 = High setting (50 mV) 1 = Low setting (26 mV) 3 CB/CL Ratio 0 = Low setting (1.8/1.9x for 26/50 mV) 1 = High setting (3.6/3.7x for 26/50 mV) 2 Current Limit Configuration 0 = Use pin settings 1 = Use SMBus settings 1 Unused 42 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5064 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |