công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

LM5064PMH/NOPB bảng dữ liệu(PDF) 18 Page - Texas Instruments

tên linh kiện LM5064PMH/NOPB
Giải thích chi tiết về linh kiện  LM5064 Negative Voltage System Power Management and Protection IC with PMBus
PDF  64 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  TI2 [Texas Instruments]
Trang chủ  https://www.ti.com
Logo TI2 - Texas Instruments

LM5064PMH/NOPB bảng dữ liệu(HTML) 18 Page - Texas Instruments

Back Button LM5064PMH/NOPB Datasheet HTML 14Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 15Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 16Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 17Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 18Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 19Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 20Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 21Page - Texas Instruments LM5064PMH/NOPB Datasheet HTML 22Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 18 / 64 page
background image
LM5064
SNVS718E – JUNE 2011 – REVISED FEBRUARY 2013
www.ti.com
Remote Temperature Sensing
The LM5064 is designed to measure temperature remotely using an MMBT3904 NPN transistor. The base and
collector of the MMBT3904 should be connected to the DIODE pin and the emitter to VEE. Place the MMBT3904
near the device that requires temperature sensing. If the temperature of the hot swap pass MOSFET, Q1, is to be
measured, the MMBT3904 should be placed as close to Q1 as the layout allows. The temperature is measured
by means of a change in the diode voltage in response to a step in current supplied by the DIODE pin. The
DIODE pin sources a constant 9.4 µA but pulses 250 µA once every millisecond in order to measure the diode
temperature. Care must be taken in the PCB layout to keep the parasitic resistance between the DIODE pin and
the MMBT3904 low so as not to degrade the measurement. Additionally, a small 1000 pF bypass capacitor
should be placed in parallel with the MMBT3904 (collector to emitter) to reduce the effects of noise. The
temperature can be read using the READ_TEMPERATURE_1 PMBus command (8Dh). The default limits of the
LM5064 will cause SMBA pin to be pulled low if the measured temperature exceeds 125°C and will disable Q1 if
the temperature exceeds 150°C. These thresholds can be reprogrammed via the PMBus interface using the
OT_WARN_LIMIT (51h) and OT_FAULT_LIMIT (4Fh) commands. If the temperature measurement and
protection capability of the LM5064 are not used, the DIODE pin should be connected to VEE.
Erroneous temperature measurements may result when the device input voltage is below the minimum operating
voltage (10V) due to VREF dropping out below the nominal voltage (2.97V). At higher ambient temperatures, this
measurement could read a value higher than the OT_FAULT_LIMIT, and will trigger a fault, disabling Q1. In this
case, the faults should be removed and the device reset by writing a 0h, followed by an 80h to the OPERATION
(01h) register.
Damaged MOSFET Detection
The LM5064 is able to detect whether the external MOSFET, Q1, is damaged under certain conditions. If the
voltage across the sense resistor exceeds 4 mV while the GATE voltage is low or the internal logic indicates that
the GATE should be low, the EXT_MOSFET_SHORTED bit in the STATUS_MFR_SPECIFIC (80h) and
DIAGNOSTIC_WORD (E1h) registers will be toggled high and the SMBA pin will be asserted unless this feature
is disabled using the ALERT_MASK register (D8h). This method effectively determines whether Q1 is shorted
because of damage present between the drain and gate and/or drain and source.
Enabling/Disabling and Resetting
The output can be disabled at any time during normal operation by either pulling the UVLO/EN pin to below its
threshold or the OVLO pin above its threshold, causing the GATE voltage to be forced low with a pull-down
strength of 4.1 mA. Toggling the UVLO/EN pin will also reset the LM5064 from a latched-off state due to an over-
current or over-power limit condition which has caused the maximum allowed number of retries to be exceeded.
While the UVLO/EN or OVLO pins can be used to disable the output they have no effect on the volatile memory
or address location of the LM5064. User stored values for address, device operation, and warning and fault
levels programmed via the SMBus are preserved while the LM5064 is powered regardless of the state of the
UVLO/EN and OVLO pins.The output may also be enabled or disabled by writing 80h or 0h to the OPERATION
(01h) register. To re-enable after a fault, the fault condition should be cleared and the OPERATION (01h) register
should be written with a 0h and then 80h.
The SMBus address of the LM5064 is captured based on the states (VEE, NC, VDD) of the ADR0, ADR1, and
ADR2 pins during turn-on and is latched into a volatile register once VDD has exceeded its POR threshold of
4.1V. Reassigning or postponing the address capture is accomplished by holding the VREF pin to VEE. Pulling
the VREF pin low will also reset the logic and erase the volatile memory of the LM5064. Once released, the
VREF pin will charge up to its final value and the address will be latched into a volatile register once the voltage
at the VREF exceeds 2.55V.
18
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: LM5064



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com