TMS320DM355 datasheet(33/153 Pages) TI

33 / 153 page

www.ti.com

2.4.13 Real Time Output (RTO) Interface

2.4.14 Pulse Width Modulator (PWM) Interface

TMS320DM355

Digital Media System-on-Chip (DMSoC)

SPRS463 – SEPTEMBER 2007

Table 2-18. Clocks Terminal Functions (continued)

TERMINAL

TYPE(1)

OTHER(2)(3)

DESCRIPTION

NAME

NO.

Output for video oscillator (27 MHz) Optional, use only if 27MHz derived from

MXI1 and PLL does not provide sufficient performance for Video DAC When the

MXO2

VDD

MXO2 is not used and powered down, the MXO2 signal should be left as a No

Connect.

The provides Real Time Output (RTO) interface.

Table 2-19. RTO Terminal Functions

TERMINAL

TYPE(1)

OTHER(2)(3)

DESCRIPTION

NAME

NO.

COUT5-

G2 /

Digital Video Out: VENC settings determine function GIO: GIO[079]

GIO079 /

I/O/Z

VDD_VOUT

PWM2A

PWM2A /

RTO0

COUT4-

B7 /

Digital Video Out: VENC settings determine function GIO: GIO[078]

GIO078 /

I/O/Z

VDD_VOUT

PWM2B

PWM2B /

RTO1

COUT3-

B6 /

Digital Video Out: VENC settings determine function GIO: GIO[077]

GIO077 /

I/O/Z

VDD_VOUT

PWM2C

PWM2C /

RTO2

COUT2-

B5 /

Digital Video Out: VENC settings determine function GIO: GIO[076]

GIO076 /

I/O/Z

VDD_VOUT

PWM2D

PWM2D /

RTO3

(1)

I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal.

(2)

Specifies the operating I/O supply voltage for each signal. See Section 5.3, Power Supplies for more detail.

(3)

PD = pull-down, PU = pull-up. (To pull up a signal to the opposite supply rail, a 1 k

Ω resistor should be used.)

The provides Pulse Width Modulator (PWM) interface.

Table 2-20. PWM Terminal Functions

TERMINAL

TYPE(1)

OTHER(2)(3)

DESCRIPTION

NAME

NO.

COUT7-

G4 /

Digital Video Out: VENC settings determine function GIO: GIO[081]

I/O/Z

VDD_VOUT

GIO081 /

PWM0

COUT6-

G3 /

Digital Video Out: VENC settings determine function GIO: GIO[080]

I/O/Z

VDD_VOUT

GIO080 /

PWM1

(1)

I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal.

(2)

Specifies the operating I/O supply voltage for each signal. See Section 5.3, Power Supplies for more detail.

(3)

PD = pull-down, PU = pull-up. (To pull up a signal to the opposite supply rail, a 1 k

Ω resistor should be used.)

Submit Documentation Feedback

Device Overview

TMS320DM355 bảng dữ liệu(PDF) 33 Page - Texas Instruments

TMS320DM355 bảng dữ liệu(HTML) 33 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL