CS5320 datasheet(93/160 Pages) AMCC

93 / 160 page

S5320 – PCI Match Maker: PCI Bus Protocol

Revision 5.03 – June 14, 2006

AMCC Confidential and Proprietary

DS1656

Data Sheet

PCI READ TRANSFERS

The S5320 responds to PCI bus memory or I/O read

transfers when it is selected as a target.

PCI targets may drive DEVSEL# and TRDY# after the

end of the address phase. TRDY# is not driven until

the target can provide valid data for the PCI read.

Read accesses from the S5320 operation registers

are shown in Figure 44. The S5320 conditionally

asserts STOP# in clock period 3 if the initiator keeps

FRAME# asserted during clock period 2 with IRDY#

asserted (indicating a burst is being attempted). Wait

states may be added by the initiator by not asserting

the signal IRDY# during clock 3 and beyond. If

FRAM E# rem a ins asser t ed, b u t IRDY# is no t

asserted, the initiator is just adding wait states, not

necessarily attempting a burst.

Figure 44. Single Data Phase PCI Bus Read of S5320

Registers or Expansion ROM

There are only two conditions where accesses to the

S5320 do not return TRDY#, but assert STOP#

instead. This condition is called a target-initiated termi-

nation or target disconnect. This can occur when a

read attempt is made to an empty Pass-Thru FIFO.

The second condition may occur when read accesses

to the expansion ROM generate a retry if the nvRAM

interface has not finished reading 4 bytes.

When burst read transfers are attempted to the S5320

operation registers, configuration registers or expan-

sion ROM, STOP# is asserted during the first data

transfer to indicate to the initiator that no further trans-

fers (data phases) are possible. This is a target-

initiated termination where the target disconnects after

the first data phase. Figure 45 shows the signal rela-

tionships during a burst read attempt to the S5320

operation registers.

For 32-bit configuration, it is recommended that the

read operation should be performed in the DWORD

boundary with the offset address increment by 4 bytes.

The starting DWORD read address should be 0, 4, 8,

C, . . .

Similarly with 16-bit configuration, the starting

read WORD boundary with the offset address incre-

ment by 2 bytes. The starting WORD read address

should be 0, 2, 4, 6, . . .

PCI WRITE TRANSFERS

Write transfers on the PCI bus are one clock period

shorter than read transfers. This is because the

AD[31:0] bus does not require a turn-around cycle

between the address and data phases.

Write accesses to the S5320 operation registers are

shown in Figure 46. Here, the S5320 asserts the sig-

nal STOP# in clock period 3. STOP# is asserted

because the S5320 does not support burst writes to

operation registers. Wait states may be added by the

initiator by not asserting the signal IRDY# during clock

2 and beyond. There is only one condition where

writes to S5320 internal registers do not return TRDY#

(but do assert STOP#). This is called a target-initiated

termination or target disconnect. This occurs when a

write attempt is made to a full Pass-Thru FIFO. The

assertion of STOP# without the assertion of TRDY#

indicates that the initiator should retry the operation

later. The S5320 will sustain a burst as long as the

FIFO is not full.

FRAME#

AD[31:0]

C/BE[3:0]#

IRDY#

TRDY#

DEVSEL#

STOP#

PCLK

Address

Data

Bus Cmd

Byte Enables

(I)

(T)

(I) Driven by Initiator

(T) Driven by Target

CS5320 bảng dữ liệu(PDF) 93 Page - Applied Micro Circuits Corporation

CS5320 bảng dữ liệu(HTML) 93 Page - Applied Micro Circuits Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL