| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
STM32H7A3VG bảng dữ liệu(PDF) 15 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32H7A3VG bảng dữ liệu(HTML) 15 Page - STMicroelectronics |
|
15 / 237 page ![]() 3.5.2 Power supply supervisor The devices have an integrated power-on reset (POR)/ power-down reset (PDR) circuitry coupled with a Brownout reset (BOR) circuitry: • Power-on reset (POR) The POR supervisor monitors VDD power supply and compares it to a fixed threshold. The devices remain in reset mode when VDD is below this threshold, • Power-down reset (PDR) The PDR supervisor monitors VDD power supply. A reset is generated when VDD drops below a fixed threshold. The PDR supervisor can be enabled/disabled through PDR_ON pin. • Brownout reset (BOR) The BOR supervisor monitors VDD power supply. Three BOR thresholds (from 2.1 to 2.7 V) can be configured through option bytes. A reset is generated when VDD drops below this threshold. • Programmable voltage detector (PVD) The PVD monitors the VDD power supply by comparing it with a threshold selected from a set of predefined values. It can also monitor the voltage level of the PVD_IN pin by comparing it with an internal VREFINT voltage reference level. • Analog voltage detector (AVD) The AVD monitors the VDDA power supply by comparing it with a threshold selected from a set of predefined values. • VBAT threshold The VBAT battery voltage level can be monitored by comparing it with two thresholds levels. • Temperature threshold A dedicated temperature sensor monitors the junction temperature and compare it with two threshold levels. 3.5.3 Voltage regulator The same voltage regulator supplies the two power domains (CD and SRD). The CD domain can be independently switched off. Voltage regulator output can be adjusted according to application needs through six power supply levels: • Run mode (VOS0 to VOS3) – Scale 0 and scale 1: high performance – Scale 2: medium performance and consumption – Scale 3: optimized performance and low-power consumption • Stop mode (SVOS3 to SVOS5) – Scale 3: peripheral with wakeup from stop mode capabilities (UART, SPI, I2C, LPTIM) are operational – Scale 4 and 5 where the peripheral with wakeup from Stop mode is disabled The peripheral functionality is disabled but wakeup from Stop mode is possible through GPIO or asynchronous interrupt. 3.5.4 SMPS step-down converter The built-in SMPS step-down converter is a highly power-efficient DC/DC non-linear switching regulator that provides lower power consumption than a conventional voltage regulator (LDO). The step-down converter can be used to: • Directly supply the VCORE domain – the SMPS step-down converter operating modes follow the device system operating modes (Run, Stop, Standby). – the SMPS step-down converter output voltage are set according to the selected VOS and SVOS bits (voltage scaling) STM32H7A3xI/G Power supply management DS13195 - Rev 8 page 15/237 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |