| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
STM32H7A3VG bảng dữ liệu(PDF) 14 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32H7A3VG bảng dữ liệu(HTML) 14 Page - STMicroelectronics |
|
14 / 237 page ![]() The USB regulator can be bypassed to supply directly VDD33USB if VDD = 3.3 V. • VDDMMC = 1.62 to 3.6 V external power supply for independent I/Os. VDDMMC can be higher than VDD. VDDMMC pin should be tied to VDD when it is not used. • VBAT = 1.2 to 3.6 V: power supply for the VSW domain when VDD is not present. • VCAP: VCORE supply, which value depends on voltage scaling (0.74 V, 0.9 V, 1.0 V, 1.1 V, 1.2 V or 1.3 V). It is configured through VOS bits in PWR_CR3 register. The VCORE domain is split into two domains the CPU domain (CD) and the Smart Run Domain (SRD). – CD domain containing most of the peripherals and the Arm® Cortex®-M7 core – SRD domain containing some peripherals and the system control. • VDDSMPS = 1.62 to 3.6 V: step-down converter power supply • VLXSMPS = VCORE or 1.8 to 2.5 V: external regulated step-down converter output • VFBSMPS = VCORE or 1.8 to 2.5 V: external step-down converter feedback voltage sense input Note: For I/O speed optimization at low VDD supply, refer to Section 3.8 General-purpose input/outputs (GPIOs). The features available on the device depend on the package (refer to Table 1. STM32H7A3xI/G features and peripheral counts). During power-up and power-down phases, the following power sequence requirements must be respected (see Figure 2. Power-up/power-down sequence): • When VDD is below 1 V, other power supplies (VDDA, VDD33USB and VDD50USB) must remain below VDD + 300 mV. • When VDD is above 1 V, all power supplies are independent (except for VDDSMPS, which must remain at the same level as VDD). During the power-down phase, VDD can temporarily become lower than other supplies only if the energy provided to the microcontroller remains below 1 mJ. This allows external decoupling capacitors to be discharged with different time constants during the power-down transient phase. Figure 2. Power-up/power-down sequence 0.3 1 VPDR 3.6 Operating mode Power-on Power-down time V VDDX(1) VDD Invalid supply area VDDX < VDD + 300 mV VDDX independent from VDD VPOR 1. VDDx refers to any power supply among VDDA, VDD33USB and VDD50USB. 2. VDD and VDDSMPS must be wired together into order to follow the same voltage sequence. STM32H7A3xI/G Power supply management DS13195 - Rev 8 page 14/237 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |