71M6541DSLASHFSLASHG datasheet(111/166 Pages) MAXIM

111 / 166 page

71M6541D/F/G and 71M6542F/G Data Sheet

Rev 5

111

5.2

I/O RAM Map – Alphabetical Order

Table 76 lists I/O RAM bits and registers in alphabetical order.

Bits with a write direction (W in column Dir) are written by the MPU into configuration RAM. Typically, they are initially stored in flash memory and

copied to the configuration RAM by the MPU. Some of the more frequently programmed bits are mapped to the MPU SFR memory space. The

remaining bits are mapped to the address space 0x2XXX. Bits with R (read) direction can be read by the MPU. Columns labeled Rst and Wk

describe the bit values upon reset and wake, respectively. No entry in one of these columns means the bit is either read-only or is powered by the

NV supply and is not initialized. Write-only bits return zero when they are read.

Locations that are shaded in grey are non-volatile (i.e., battery-backed).

Table 76: I/O RAM Map – Functional Order

Name

Location

Rst Wk

Dir

Description

ADC_E

2704[4]

R/W Enables ADC and VREF. When disabled, reduces bias current.

ADC_DIV

2200[5]

R/W

ADC_DIV controls the rate of the ADC and FIR clocks.

The ADC_DIV setting determines whether MCK is divided by 4 or 8:

0 = MCK/4

1 = MCK/8

The resulting ADC and FIR clock is as shown below.

PLL_FAST = 0

PLL_FAST = 1

MCK

6.291456 MHz

19.660800 MHz

ADC_DIV = 0

1.572864 MHz

4.9152 MHz

ADC_DIV = 1

0.786432 MHz

2.4576 MHz

BCURR

2704[3]

R/W Connects a 100 µA load to the battery selected by TEMP_BSEL.

BSENSE[7:0]

2885[7:0]

–

The result of the battery measurement. See 2.5.6 71M654x Battery Monitor.

CE_E

2106[0]

R/W CE enable.

CE_LCTN[5:0]

2109[5:0]

31 31 R/W

CE program location. The starting address for the CE program is

1024*CE_LCTN.

CHIP_ID[15:8]

CHIP_ID[7:0]

2300[7:0]

2301[7:0]

These bytes contain the chip identification.

CHOP_E[1:0]

2106[3:2]

R/W

Chop enable for the reference bandgap circuit. The value of CHOP changes

on the rising edge of MUXSYNC according to the value in CHOP_E:

00 = toggle

01 = positive

10 = reversed

11 = toggle

1except at the mux sync edge at the end of an accumulation interval.

71M6541D/F/G bảng dữ liệu(PDF) 111 Page - Maxim Integrated Products

71M6541D/F/G bảng dữ liệu(HTML) 111 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL