| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
DA9072 bảng dữ liệu(PDF) 32 Page - Dialog Semiconductor |
|
|
|||||||||||||||||||||||||||||
DA9072 bảng dữ liệu(HTML) 32 Page - Dialog Semiconductor |
|
32 / 113 page ![]() DA9072 Ultra-Low Quiescent Current PMIC Datasheet Revision 3.0 14-Jun-2021 CFR0011-120-00 32 of 113 © 2021 Dialog Semiconductor Equation 1: ����(��������) = ����(����������������) × ����(������������) × ( 1 0.398 − 1 0.15 ) ����(������������) × ( 1 0.15 − 1) − ����(����������������) × ( 1 0.398 − 1) Equation 2: ����(��������) = ( 1 0.398 − 1) ( 1 ����(��������) + 1 ����(����������������) ) Where ● R(HOT) = the NTC resistance at the hot temperature ● R(COLD) = the NTC resistance at the cold temperature The cool and warm thresholds are not independently programmable and are fixed once the cold and hot values are determined. The cool and warm thresholds can be determined by the NTC value at the threshold: Equation 3: ����(����������������) = ����(��������) × ����(��������) × 0.35 ����(��������) − ����(��������) × 0.35 − ����(��������) × 0.35 Equation 4: ����(����������������) = ����(��������) × ����(��������) × 0.205 ����(��������) − ����(��������) × 0.205 − ����(��������) × 0.205 Where ● R(COOL) = the NTC resistance at the cool temperature ● R(WARM) = the NTC resistance at the warm temperature Temp Sense Modes of Operation The DA9072 provides two modes of battery temperature sense control: Auto mode and Host Control mode. In Auto mode, the DA9072 enables the VTEMP voltage every 2 s or every 50 ms depending on the VDD_PWR state. At the start of each cycle, the VTEMP voltage is activated for 10 ms after which the TEMP_SNS voltage is checked. This timing is shown in Figure 22. Auto mode does not rely on the host to operate; therefore, it is ideally suited to provide continuous safety monitoring. In battery powered operation, VTEMP is enabled for only 0.5 % of the time which reduces the typical current required for temperature sensing to less than 1 µA. While VDD_PWR is applied, the Temp Sense function is in Auto mode and host control of the VTEMP period is not available. This is illustrated in the Active Power section of Figure 22. If lower current consumption is needed, temperature sensing can be controlled by the host. In host- controlled mode, an I2C command activates the same 10 ms VTEMP and TEMPS_SNS cycle. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |