| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
DA9072 bảng dữ liệu(PDF) 43 Page - Dialog Semiconductor |
|
|
|||||||||||||||||||||||||||||
DA9072 bảng dữ liệu(HTML) 43 Page - Dialog Semiconductor |
|
43 / 113 page ![]() DA9072 Ultra-Low Quiescent Current PMIC Datasheet Revision 3.0 14-Jun-2021 CFR0011-120-00 43 of 113 © 2021 Dialog Semiconductor Connect a resistor (RITER_CHG) from the ITER_CHG pin to ground. Table 32 shows the recommended resistor values to set the pre-charge and termination currents. Table 32: ITER_CHG Pin Recommended Resistor Values % of ICHG (Typ) Resistance (k Ω) 5 68 10 22 15 8.2 20 2.2 Register setting at 0x0023 is used 0 Once VDD_PWR is connected, ICHG_PRE and ITER values can be read at register 0x0020 [5:4]. ICHG_PRE cannot be set higher than 50 mA, or lower than 0.5 mA. Settings which are out of range result in the minimum or maximum current setting. For example, with a 400 mA fast charge current, a 20 % setting would result in 80 mA, but the actual pre-charge current is the maximum value, 50 mA. 4.7.2 Input Current Limit Programming VDD_PWR input current limit (IDDPWR_LIM) is programmed by a resistor connected from the ILIM_PWR pin to ground. The resistor value is calculated as: ��������������������_������������(Ω) = 1000 ������������������������_������������(����) Not all current limit register settings are available in Resistor Setting mode. The available current limit settings and corresponding resistor values are shown in Table 33. Table 33: ILIM_PWR Pin Recommended Resistor Values IDDPWR_LIM (Typ) Resistance (k Ω) Register setting at 0x0027 is used 0 600 mA 1.6 500 mA 2.0 400 mA 2.7 300 mA 3.6 200 mA 5.1 150 mA 6.8 100 mA 10.0 50 mA 20.0 4.7.3 Charge Current Programming Fast charge current (ICHG) is programmed by a resistor connected from the ILIM_CHG pin to ground. The resistor value is calculated as: ��������������������_������������(Ω) = 1000 ����������������(����) Not all fast charge register settings are available. The available current limit settings and corresponding resistor values are shown in Table 34. Table 34: ILIM_CHG Pin Recommended Resistor Values ICHG (Typ) Resistance (k Ω) Register setting at 0x0022 is used 0 500 mA 2.0 400 mA 2.7 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |