| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ML9092-01TB bảng dữ liệu(PDF) 45 Page - OKI electronic componets |
|
|
|||||||||||||||||||||||||||||
ML9092-01TB bảng dữ liệu(HTML) 45 Page - OKI electronic componets |
|
45 / 66 page ![]() FEDL9092-01 OKI Semiconductor ML9092-01/02/03/04 45/66 Duty Y register setting range and loop range Invalid address setting range 1/8 0 to 7 (00H to 07H) 0 to 7 (00H to 07H) 1/9 0 to 8 (00H to 08H) 0 to 8 (00H to 08H) 1/10 0 to 9 (00H to 09H) 0 to 9 (00H to 09H) This register is reset to “0” when the RESET pin is made low. • Port register A (PTA) set D7 D6 D5 D4 D3 D2 D1 D0 — PTA —: don’t care The port register A set instruction sets the output of port A. When the PTA bit is set to “1”, a “H” level is output from the PA0 pin of general purpose port A. In the same way, when the PTA bit is set to “0”, a “L” level is output from the PA0 pin. If the RESET pin is pulled to a “L” level, the PE bit (bit D2) of the control register is reset to “0”, this register is reset to “0”, and the PA0 pin goes to high impedance. After the reset state is released, if the PTA bit of this register is set to “1” or “0” and then the PE bit is set to “1”, the PA0 pin is released from its high impedance state and a “H” or “L” level that corresponds to the set status of the PTA bit, is output from the PA0 pin. • Port register B (PTB) set D7 D6 D5 D4 D3 D2 D1 D0 — PTB2 PTB1 PTB0 —: don’t care The port register B set instruction sets the output of port B. (Applies to the ML9092-01/04.) When each bit of PTB0 to PTB2 is set to “1”, the PWM signal set in the PWM0 to PWM2 registers is output from each of the PB0 to PB2 pins of the general purpose port B. In the same way, when each bit of PTB0 to PTB2 is set to “0”, each of the PB0 to PB2 pins are pulled to a “L” level. If the RESET pin is pulled to a “L” level, the PE bit (bit D2) of the control register is reset to “0”, this register is reset to “0”, and the PB0 to PB2 pins go to high impedance. After the reset state is released, if the a PWM value is set in the PWM0 to PWM2 registers and then the PE bit is set to “1”, the PB0 to PB2 registers are released from their high impedance state and a PWM waveform is output. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |