ML9092-01TB datasheet(16/66 Pages) OKI

16 / 66 page

FEDL9092-01

OKI Semiconductor

ML9092-01/02/03/04

16/66

• R0/C0 to R4/C4 (ML9092-01), R0 to R5 (ML9092-02/03), R0 to R4 (ML9092-04)

Key switch scan signal output pins. During the scan operation, “L” level signals are output in the order of R0/C0,

R1/C1, ..., R4/C4 (ML9092-01) or R0, R1, ..., R5 (ML9092-02/03) or R0, R1, ..., R4 (ML9092-04). (Refer to the

description under the heading “Key scan” for details.) For the ML9092-01, R0 to R4 can be used as the output

ports for the general-purpose port C depending on the input signal to the KPS pin.

• C0/D0 to C4/D4 (ML9092-01), C0 to C3 (ML9092-02/03), C0 to C4 (ML9092-04)

Input pins that detect the key switch status. Pull-up resistors and a Schmitt circuit are internally connected to these

pins.

Assemble a key matrix between these pins and the R0/C0 to R4/C4 (ML9092-01) or R0 to R5

(ML9092-02/03) or R0 to R4 (ML9092-04) pins. For the ML9092-01, C0 to C4 can be used as the output ports for

the general-purpose port D depending on the input signal to the KPS pin.

• KPS

Input pin that selects whether the R0/C0 to R4/C4 pins and C0/D0 to C4/D4 pins are used to detect the key switch

status or whether they are used as the output pins for the general-purpose ports C and D. When this pin is pulled to

a “H” level, the R0/C0 to R4/C4 pins and C0/D0 to C4/D4 pins function as pins that detect the key switch status.

When this pin is pulled to a “L” level, it functions as the output pin for the general-purpose ports C and D. This pin

must be fixed at either a “H” or “L” level.

This pin is provided only for the ML9092-01.

• A, B

Input pins for encoder format rotary switches. A Schmitt circuit is internally connected to these pins. When

turning the rotary switch clockwise, input to the A pin a signal more advancing in phase than the B pin. When

turning the rotary switch counterclockwise, input to the B pin a signal more advancing in phase than the A pin.

• PA0

General-purpose port A output pin. This pin can output a current of –15 mA. If this pin is used to drive an LED,

insert an external current limiting resistor in series with the LED. If this pin is not used, leave it unconnected

(open).

• PB0 to PB2

Port B pins, which are used for PWM outputs. These pins are provided for the ML9092-01/04. Any pins not to be

used should be left unconnected (open).

• SEG1 to SEG60(56)

Segment signal output pins for LCD driving. Any pins not to be used should be left unconnected (open). For the

ML9092-01, only SEG1 to SEG56 apply.

• COM1 to COM10

Common signal output pins for LCD driving. Any pins not to be used should be left unconnected (open).

• V

Logic power supply connection pin.

• V

Power supply GND connection pin.

• V

Voltage doubler reference voltage input pin. A voltage twice that which is input to this pin is output to the VOUT

pin. When the voltage doubler is not used, connect this pin to GND.

This pin is provided for the ML9092-01/02.

ML9092-01TB bảng dữ liệu(PDF) 16 Page - OKI electronic componets

ML9092-01TB bảng dữ liệu(HTML) 16 Page - OKI electronic componets

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

bảng dữ liệu tải về

Link URL