LAN9220 datasheet(51/142 Pages) MICROCHIP

51 / 142 page

 2006-2017 Microchip Technology Inc.

DS00002417A-page 51

LAN9220

3.12.7

TRANSMITTER ERRORS

If the Transmitter Error (TXE) flag is asserted for any reason, the transmitter will continue operation. TX Error (TXE) will

be asserted under the following conditions:

• If the actual packet length count does not match the Packet Length field as defined in the TX command.

• Both TX command ‘A’ and TX command ‘B’ are required for each buffer in a given packet. TX command ‘B’ must

be identical for every buffer in a given packet. If the TX command ‘B’ words do not match, the Ethernet controller

will assert the Transmitter Error (TXE) flag.

• Host overrun of the TX data FIFO.

• Overrun of the TX status FIFO (unless TXSAO is enabled)

3.12.8

STOPPING AND STARTING THE TRANSMITTER

To halt the transmitter, the host must set the TX_STOP bit in the TX_CFG register. The transmitter will finish sending

the current frame (if there is a frame transmission in progress). When the transmitter has received the TX status for this

frame, it will clear the TX_STOP and TX_ON bits, and will pulse the TXSTOP_INT.

Once stopped, the host can optionally clear the TX status and TX data FIFOs. The host must re-enable the transmitter

by setting the TX_ON bit. If the there are frames pending in the TX data FIFO (i.e., TX data FIFO was not purged), the

transmission will resume with this data.

3.13

RX Data Path Operation

When an Ethernet Packet is received, the MIL first begins to transfer the RX data. This data is loaded into the RX data

FIFO. The RX data FIFO pointers are updated as data is written into the FIFO.

The last transfer from the MIL is the RX status word. The LAN9220 implements a separate FIFO for the RX status words.

The total available RX data and status queued in the RX FIFO can be read from the RX_FIFO_INF register. The host

may read any number of available RX status words before reading the RX data FIFO.

The host must use caution when reading the RX data and status. The host must never read more data than what is

available in the FIFOs. If this is attempted an underrun condition will occur. If this error occurs, the Ethernet controller

will assert the Receiver Error (RXE) interrupt. If an underrun condition occurs, a soft reset is required to regain host

synchronization.

A configurable beginning offset is supported in the LAN9220. The RX data Offset field in the RX_CFG register controls

the number of bytes that the beginning of the RX data buffer is shifted. The host can set an offset from 0-31 bytes. The

offset may be changed in between RX packets, but it must not be changed during an RX packet read.

The LAN9220 can be programmed to add padding at the end of a receive packet in the event that the end of the packet

does not align with the host burst boundary. This feature is necessary when the LAN9220 is operating in a system that

always performs multi-DWORD bursts. In such cases the LAN9220 must ensure that it can transfer data in multiples of

the Burst length regardless of the actual packet length. When configured to do so, the LAN9220 will add extra data at

the end of the packet to allow the host to perform the necessary number of reads so that the Burst length is not cut short.

Once a packet has been padded by the H/W, it is the responsibility of the host to interrogate the Packet length field in

the RX status and determine how much padding to discard at the end of the Packet.

It is possible to read multiple packets out of the RX data FIFO in one continuous stream. It should be noted that the

programmed Offset and Padding will be added to each individual packet in the stream, since packet boundaries are

maintained.

3.13.1

RX SLAVE PIO OPERATION

Using PIO mode, the host can either implement a polling or interrupt scheme to empty the received packet out of the

RX data FIFO. The host will remain in the idle state until it receives an indication (interrupt or polling) that data is avail-

able in the RX data FIFO. The host will then read the RX status FIFO to get the packet status, which will contain the

packet length and any other status information. The host should perform the proper number of reads, as indicated by

the packet length plus the start offset and the amount of optional padding added to the end of the frame, from the RX

data FIFO.

LAN9220 bảng dữ liệu(PDF) 51 Page - Microchip Technology

LAN9220 bảng dữ liệu(HTML) 51 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL