AM79C875KC datasheet(11/48 Pages) AMD

11 / 48 page

Am79C875

MDIO

Management Data I/O

Input/Output, Pull-Down

This pin is a bidirectional data interface used by the

MAC to access management register within the Net-

PHY™ 4LP device. This pin has an internal pull-down,

therefore, it requires an external pull-up resistor (1.5

Ω) as specified in IEEE-802.3 section 22.

MDC

Management Data Clock

Input, Pull-Down

This pin is the serial management clock which is used

to clock MDIO data to the MAC.

RST

Reset

Input, Pull-Up

An active low input will force the NetPHY™ 4LP device

to a known reset state. Reset also can be done through

the internal power-on-reset or MII Register 0, bit 15.

INTR

Interrupt

Tri-State

This pin is true whenever the NetPHY™ 4LP device

detects an event flagged as an interrupt. Events to be

flagged are programmed in Register 17. Interrupts are

cleared on Read. The polarity of INTR (active HIGH or

active LOW) is set by Register 16, bit 14. The default is

active LOW, which requires a 10 K

Ω pull-up resistor.

LED Port

Note: Consult the LED Port Configuration section for

appropriate pull-up and pull-down resistors.

LEDDPX[0]/FX_DIS

Port [0] Duplex LED

Input/Output, Pull-Up

Low LED indicates full-duplex and high indicates half-

duplex.

FX Mode: Pulled low at reset will put Port 3 in

100BASE-FX mode.

LEDACT_LINK[0]

Port [0] Transmit/Receive Activity LED

Output, Pull-Up

LED is output low for approximately 30 ms each time

there is activity. LINK is an active low signal. This signal

should have a 1k–4.7K

Ω pull-up resistor.

LEDSPD[0]/TP1_1

Port [0] Speed LED

Input/Output, Pull-Up

LED is output low when operating in 100BASE-X

modes and high when operating in 10BASE-T modes.

TP1_1: Pulled low at reset will select transmit trans-

former ratio to be 1.25:1. Default is 1:1 transformer.

LEDDPX[1]/PHYAD[4]

Port [1] Duplex LED

Input/Output, Pull-Up

LED low indicates full-duplex and high indicates half-

duplex.

PHY Address[4]. This is the first address bit received

in the management frame, and one of three MSBs for

MII management PHY address. The two LSBs, PHYAD

[1:0] are internally wired to four ports: PHYAD

[11]=Port3,..., PHYAD [00] = Port0. The PHYAD will

also determine the scramble seed, this will help to

reduce EMI when there are multiple ports switching at

the same time. To set this pin, use pull-up or pull-down

resistors in the range of 1 K

Ω to 4.7 KΩ.

LEDACT_LINK[1]/PHYAD[3]

Port [1] Transmit/Receive Activity LED

Input/Output, Pull-Up

LED is output low for approximately 30 ms each time

there is activity. LINK is an active low signal.

PHY Address[3]. This is the second MSB and one of

three MSB’s for MII management PHY address. To set

this pin, use pull-up or pull-down resistors in the range

of 1 K

Ω to 4.7 KΩ.

LEDSPD[1]/PHYAD[2]

Port [1] Speed LED

Input/Output, Pull-Up

LED is output low when operating in 100BASE-X

modes and high when operating in 10BASE-T modes.

PHY Address[2]. This is the third MSB and one of

three MSB’s for MII management PHY address. To set

this pin, use pull-up or pull-down resistors in the range

of 1 K

Ω to 4.7 KΩ.

LEDDPX[2]/DPLX

Port [2] Duplex LED

Input/Output, Pull-Up

LED low indicates full-duplex and high indicates half-

duplex.

DPLX: Full Duplex Mode Enable. This pin is logically

OR’ed with a full-duplex enable MII control bit to gener-

ate an internal full-duplex enable signal. When as-

serted high, the NetPHY™ 4LP device operates in full-

duplex mode as determined through Auto-Negotiation

or software setting. When asserted low, the internal

control bit (Register 0, bit 8) will determine the full-du-

plex operating mode.

LEDACT_LINK[2]

Port [2] Transmit/Receive Activity LED

Output, Pull-Up

LED is output low for approximately 30 ms each time

there is activity. LINK is an active low signal. This signal

should have a 1k–4.7K

Ω pull-up.

LEDSPD[2]/FORCE100

Port [2] Speed LED

Input/Output, Pull-Up

LED is output low when operating in 100BASE-X

modes and high when operating in 10BASE-T modes.

FORCE100: Force 100BASE-X Operation. When this

signal is pulled high and ANEGA is low at reset, all

ports will be forced to 100BASE-TX operation. When

asserted low and ANEGA is low, all ports are forced to

AM79C875KC bảng dữ liệu(PDF) 11 Page - Advanced Micro Devices

AM79C875KC bảng dữ liệu(HTML) 11 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

bảng dữ liệu tải về

Link URL