| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PIC18F4331 bảng dữ liệu(PDF) 181 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC18F4331 bảng dữ liệu(HTML) 181 Page - Microchip Technology |
|
181 / 396 page ![]() 2003 Microchip Technology Inc. Preliminary DS39616B-page 179 PIC18F2331/2431/4331/4431 FIGURE 16-14: FILTER TIMING DIAGRAM (CLOCK DIVIDER = 1:1) 16.4 IC and QEI Shared Interrupts The IC and QEI sub-modules can each generate three distinct interrupt signals; however, they share the use of the same three interrupt flags in register PIR3. The meaning of a particular interrupt flag at any given time depends on which module is active at the time the interrupt is set. The meaning of the flags in context are summarized in Table 16-7. When the IC submodule is active, the three flags (IC1IF, IC2QEIF and IC3DRIF) function as interrupt-on-capture event flags for their respective input capture channels. The channel must be configured for one of the events that will generate an interrupt (see Section 16.1.7 “IC Interrupts” for more information). When the QEI is enabled, the IC1IF interrupt flag indicates an interrupt caused by a velocity measurement event, usually an update of the VELR register. The IC2QEIF interrupt indicates that a position measurement event has occurred. IC3DRIF indicates that a direction change has been detected. TABLE 16-7: MEANING OF IC AND QEI INTERRUPT FLAGS 16.5 Operation in Sleep Mode 16.5.1 3X INPUT CAPTURE IN SLEEP MODE Since the input capture can operate only when its time base is configured in a Synchronous mode, the input capture will not capture any events. This is because the device’s internal clock has been stopped, and any internal timers in synchronous modes will not incre- ment. The prescaler will continue to count the events (not synchronized). When the specified capture event occurs, the CAPxIF interrupt will be set. The Capture Buffer register will be updated upon wake-up from sleep to the current TMR5 value. If the CAPxIF interrupt is enabled, the device will wake-up from sleep. This effectively enables all input capture channels to be used as the external interrupts. 16.5.2 QEI IN SLEEP MODE All QEI functions are halted in Sleep mode. CAP1/INDX pin(1) TCY Noise glitch(3) CAP1/INDX input(2) TGD = 3TCY Noise glitch(3) TQEI = 16TCY Note 1: Only CAP1/INDX pin input is shown for simplicity. Similar event timing occurs on CAP2/QEA and CAP3/QEB pins. 2: Noise filtering occurs in shaded portions of CAP1 input. 3: Filter’s group delay: TGD = 3 TCY. (input to filter) (output from filter) Interrupt Flag Meaning IC Mode QEI Mode IC1IF IC1 capture event Velocity register update IC2QEIF IC2 capture event Position measurement update IC3DRIF IC3 capture event Direction change |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |