| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PIC18F4331 bảng dữ liệu(PDF) 177 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC18F4331 bảng dữ liệu(HTML) 177 Page - Microchip Technology |
|
177 / 396 page ![]() 2003 Microchip Technology Inc. Preliminary DS39616B-page 175 PIC18F2331/2431/4331/4431 FIGURE 16-11: QEI MODULE RESET TIMING WITH THE INDEX INPUT 16.2.6 VELOCITY MEASUREMENT The velocity pulse generator, in conjunction with the IC1 and the synchronous TMR5 (in synchronous operation), provides a method for high accuracy speed measurements at both low and high mechanical motor speeds. The Velocity mode is enabled when the VELM bit is cleared (= 0) and QEI is set to one of its operating modes (see Table 16-6). To optimize register space, the input capture channel one (IC1) is used to capture TMR5 counter values. Input capture buffer register, CAP1BUF, is redefined in Velocity Measurement mode, VELM = 0, as the Velocity Register buffer (VREGH, VREGL). TABLE 16-6: VELOCITY PULSES QEB QEA UP/DOWN IC2QEIF POSCNT(1) count (+/-) +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 MAXCNT MAXCNT=1527 Q4(3) Q4(3) INDX Q1(4) Q1(5) Position counter load Forward Reverse Note 2 Note 2 Note 1: POSCNT register is shown in QEI x4 Update mode (POSCNT increments on every rising and every falling edge of QEA and QEB input signals) 2: When INDX Reset pulse is detected, POSCNT is reset to ‘0’ on the next QEA or QEB edge. POSCNT is set to MAXCNT when POSCNT = 0 (when decrementing), which occurs on the next QEA or QEB edge. Similar Reset sequence occurs for the reverse direction except that the INDX signal is recognized on its falling edge. The Reset is generated on the next QEA or QEB edge. 3: IC2QEI is enabled for one TCY clock cycle. 4: Position counter is loaded with ‘0000h’ (i.e., Reset) on the next QEA or QEB edge when INDX is high. 5: Position counter is loaded with MAXCNT value (e.g., 1527h) on the next QEA or QEB edge following the INDX falling edge input signal detect). 6: IC2QEIF must be cleared in software. Note 6 QEIM<2:0> Velocity Event Mode 001 010 x2 Velocity Event mode. The velocity pulse is generated on every QEA edge. 101 110 x4 Velocity Event mode. The velocity pulse is generated on every QEA and QEB active edge. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |