| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PIC18F4331 bảng dữ liệu(PDF) 179 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC18F4331 bảng dữ liệu(HTML) 179 Page - Microchip Technology |
|
179 / 396 page ![]() 2003 Microchip Technology Inc. Preliminary DS39616B-page 177 PIC18F2331/2431/4331/4431 FIGURE 16-13: VELOCITY MEASUREMENT TIMING(1) 16.2.6.2 Velocity Postscaler The velocity event pulse (velcap, see Figure 16-12) serves as the TMR5 capture trigger to IC1 while in the Velocity mode. The number of velocity events are reduced by the velocity postscaler before they are used as the input capture clock. The velocity event reduction ratio can be set with the PDEC1:PDEC0 control bits (QEICON<1:0>) to 1:4, 1:16, 1:64 or no reduction (1:1). The velocity postscaler settings are automatically reloaded from their previous values as the Velocity mode is re-enabled. 16.2.6.3 CAP1REN in Velocity Mode The TMR5 value can be reset (TMR5 register pair = 0000h) on a velocity event capture by setting the CAP1REN bit (CAP1CON<6>). When CAP1REN is cleared, the TMR5 time base will not be reset on any velocity event capture pulse. The VELR register pair, however, will continue to be updated with the current TMR5 value. QEB QEA cnt_reset(3) TMR5(2) velcap BCF TMR5CON, VELM VELR(2) 1529 1537 vel_out Old Value Forward Q1 Q1 IC1IF(4) Q1 Instr. Execution MOVWF QEICON(5) BCF PIE2, IC1IE BSF PIE2, IC1IE CAP1REN Note 1: Timing shown is for QEIM<2:0> = 101, 110 or 111 (x4 Update mode enabled) and the velocity postscaler divide ratio is set to divide by 4 (PDEC<1:0> = 01). 2: VELR register latches the TMR5 count on the “velcap” capture pulse. Timer5 must be set to the synchronous timer or Counter mode. In this example, it is set to the Synchronous Timer mode where the TMR5 prescaler divide ratio = 1 (i.e., Timer5 clock = TCY). 3: The TMR5 counter is reset on the next Q1 clock cycle following the “velcap” pulse. TMR5 value is unaffected when the Velocity Measurement mode is first enabled (VELM = 0). The velocity postscaler values must be reconfigured to their previous settings when re-entering Velocity Measurement mode. While making speed measurements of very slow rotational speeds (e.g., servo-controller applications), the Velocity Measurement mode may not provide sufficient precision. The Pulse Width Measurement mode may have to be used to provide the additional precision. In this case, the input pulse is measured on the CAP1 input pin. 4: IC1IF interrupt is enabled by setting IC1IE as follows, BSF PIE2, IC1IE. Assume IC1E bit is placed in PIE2 Peripheral Interrupt Enable register in the target device. The actual IC1IF bit is written on Q2 rising edge. 5: Post decimation value is changed from PDEC = 01 (decimate by 4) to PDEC = 00 (decimate by 1). Reverse |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |