| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PIC18F4331 bảng dữ liệu(PDF) 180 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC18F4331 bảng dữ liệu(HTML) 180 Page - Microchip Technology |
|
180 / 396 page ![]() PIC18F2331/2431/4331/4431 DS39616B-page 178 Preliminary 2003 Microchip Technology Inc. 16.3 Noise Filters The Motion Feedback module includes three noise rejection filters on CAP1/INDX, CAP2/QEA and CAP3/QEB. The filter block also includes a fourth filter for the T5CKI pin. They are intended to help reduce spurious noise spikes which may cause the input sig- nals to become corrupted at the inputs. The filter ensures that the input signals are not permitted to change until a stable value has been registered for three consecutive sampling clock cycles. The filters are controlled using the Digital Filter Control (DFLTCON) register (see Register 16-3). The filters can be individually enabled or disabled by setting or clearing the corresponding FLTxEN bit in the DFLTCON register. The sampling frequency, which must be the same for all three noise filters, can be programmed by the FLTCK2:FLTCK0 configuration bits. TCY is used as the clock reference to the clock divider block. The noise filters can either be added or removed from the input capture or QEI signal path by setting or clearing the appropriate FLTxEN bit, respectively. Each capture channel provides for individual enable control of the filter output. The FLT4EN bit enables or disabled the noise filter available on TMR5CKI input in the Timer5 module. The filter network for all channels is disabled on POR and BOR resets , as the DFLTCON register is cleared on resets. The operation of the filter is shown in the timing diagram in Figure 16-14. REGISTER 16-3: DFLTCON: DIGITAL FILTER CONTROL REGISTER U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — FLT4EN FLT3EN FLT2EN FLT1EN FLTCK2 FLTCK1 FLTCK0 bit 7 bit 0 bit 7 Unimplemented: Read as ‘0’ bit 6 FLT4EN: Noise Filter Output Enable bit, T5CKI input 1 = Enabled 0 = Disabled bit 5 FLT3EN: Noise Filter Output Enable bit, CAP3/QEB input(1) 1 = Enabled 0 = Disabled bit 4 FLT2EN: Noise Filter Output Enable bit, CAP2/QEA input(1) 1 = Enabled 0 = Disabled bit 3 FLT1EN: Noise Filter Output Enable bit, CAP1/INDX input(1) 1 = Enabled 0 = Disabled bit 2-0 FLTCK<2:0>: Noise Filter Clock Divider Ratio bits 111 =Unused 110 =1:128 101 =1:64 100 =1:32 011 =1:16 010 =1:4 001 =1:2 000 =1:1 Note 1: Noise Filter Output Enables are functional in both QEI and IC operating modes Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = bit is set ‘0’ = bit is cleared x = bit is unknown Note: The Noise Filter is intended for random high-frequency filtering and not continuous high-frequency filtering. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |