| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PIC18F4331 bảng dữ liệu(PDF) 100 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC18F4331 bảng dữ liệu(HTML) 100 Page - Microchip Technology |
|
100 / 396 page ![]() PIC18F2331/2431/4331/4431 DS39616B-page 98 Preliminary 2003 Microchip Technology Inc. REGISTER 9-6: PIR3: PERIPHERAL INTERRUPT FLAG REGISTER 3 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — PTIF IC3DRIF IC2QEIF IC1IF TMR5IF bit 7 bit 0 bit 7-5 Unimplemented: Read as ‘0’ bit 4 PTIF: PWM Time Base Interrupt bit 1 = PWM Time Base matched the value in PTPER register. Interrupt is issued according to the postscaler settings. PTIF must be cleared in software. 0 = PWM Time Base has not matched the value in PTPER register. bit 3 IC3DRIF: IC3 Interrupt Flag/Direction Change Interrupt Flag bit IC3 Enabled (CAP3CON<3:0>) 1 = TMR5 value was captured by the active edge on CAP3 input (must be cleared in software). 0 = TMR5 capture has not occurred. QEI Enabled (QEIM<2:0>) 1 = Direction of rotation has changed (must be cleared in software). 0 = Direction of rotation has not changed. bit 2 IC2QEIF: IC2 Interrupt Flag/QEI Interrupt Flag bit IC2 Enabled (CAP2CON<3:0>) 1 = TMR5 value was captured by the active edge on CAP2 input (must be cleared in software). 0 = TMR5 capture has not occurred. QEI Enabled (QEIM<2:0>) 1 = The QEI position counter has reached the MAXCNT value or the index pulse, INDX, has been detected. Depends on the QEI operating mode enabled. Must be cleared in software. 0 = The QEI position counter has not reached the MAXCNT value or the index pulse has not been detected. bit 1 IC1IF: IC1 Interrupt Flag bit IC1 Enabled (CAP1CON<3:0>) 1 = TMR5 value was captured by the active edge on CAP1 input (must be cleared in software). 0 = TMR5 capture has not occurred. QEI Enabled (QEIM<2:0>) and Velocity Measurement mode enabled (VELM = 0 in QEICON Register) 1 = Timer5 value was captured by the active velocity edge (based on PHA or PHB input). CAP1REN bit must be set in CAP1CON register. IC1IF must be cleared in software. 0 = Timer5 value was not captured by the active velocity edge. bit 0 TMR5IF: Timer5 Interrupt Flag bit 1 = Timer5 time base matched the PR5 value (must be cleared in software). 0 = Timer5 time base did not match the PR5 value. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = bit is set ‘0’ = bit is cleared x = bit is unknown |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |