| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
WM8903 bảng dữ liệu(PDF) 82 Page - Wolfson Microelectronics plc |
|
|
|||||||||||||||||||||||||||||
WM8903 bảng dữ liệu(HTML) 82 Page - Wolfson Microelectronics plc |
|
82 / 178 page ![]() WM8903 Production Data w PD, Rev 4.5, June 2012 82 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION R67 (43h) DC Servo 0 4 DCS_MASTER_ENA 1 DC Servo Master Control 0 = DC Servo Reset 1 = DC Servo Enabled 3:0 DCS_ENA [3:0] 0000 DC Servo Enable [3] - HPOUTL enable [2] - HPOUTR enable [1] - LOUTL enable [0] - LOUTR enable R69 (45h) DC Servo 2 1:0 DCS_MODE [1:0] 00 DC Servo Mode 00 = WRITE_STOP 01 = WRITE_UPDATE 10 = START_STOP 11 = START_UPDATE Table 54 DC Servo Control To reduce power consumption when unused audio outputs are disabled, the DC Servo correction should also be disabled. The WM8903 provides the capability to quickly resume the necessary DC Servo correction when the outputs are re-enabled, without the time delay associated with the START_STOP mode of DC Servo operation. If the DC Servo correction is disabled using the DCS_ENA bits, but the DCS_MASTER_ENA bit is maintained at 1, then the DC Servo will retain the latest correction values in its memory. These values will be re-applied when the DC Servo is later enabled via the DCS_ENA bits. An alternative method to apply known correction settings is to read the correction values from the WM8903 register map and to store these for later use. After DC offset correction has been performed, the applicable correction values can be read from the fields in the Servo Readback registers R81 to R84 described in Table 55. Setting DCS_MODE to 00b or 01b selects WRITE_STOP mode and WRITE_UPDATE mode respectively. WRITE_STOP mode is similar to START_STOP mode, except that the DC Servo correction factors are read from internal registers, instead of being calculated from the measured output conditions. In the same way, WRITE_UPDATE mode is similar to START_UPDATE mode. When the DC Servo is commanded to one of these modes, the initial DC offset correction values are read from the _WRITE_VAL field in registers R71 to R74 described in Table 55. Selecting WRITE_STOP or WRITE_UPDATE mode applies initial settings which should be written to registers R71 to R74 before the DC Servo is enabled. In WRITE_STOP mode, no further DC correction is applied. In WRITE_UPDATE mode, the DC Servo will periodically measure and adjust the DC offset correction. Similar to START_UPDATE mode, the default time between updates is approximately 10 minutes. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |