CYWUSB6953_10 datasheet(45/68 Pages) CYPRESS

45 / 68 page

CYRF69103

Document #: 001-07611 Rev *F

Page 45 of 68

19.5 SPI Data Register

When an interrupt occurs to indicate to firmware that an byte of receive data is available, or the transmitter holding register is empty,

firmware has 7 SPI clocks to manage the buffers—to empty the receiver buffer, or to refill the transmit holding register. Failure to meet

this timing requirement results in incorrect data transfer.

19.6 SPI Configure Register

Table 19-14. SPI Data Register (SPIDATA) [0x3C] [R/W]

Bit #

Field

SPIData[7:0]

Read/Write

R/W

Default

When read, this register returns the contents of the receive buffer. When written, it loads the transmit holding register.

Bits 7:0

SPI Data [7:0]

Table 19-15. SPI Configure Register (SPICR) [0x3D] [R/W]

Bit #

Field

Swap

LSB First

Comm Mode

CPOL

CPHA

SCLK Select

Read/Write

R/W

Default

Bit 7

Swap

0 = Swap function disabled.

1 = The SPI block swaps its use of SMOSI and SMISO. Among other things, this can be useful in implementing

single wire SPI-like communications.

Bit 6

LSB First

0 = The SPI transmits and receives the MSB (Most Significant Bit) first.

1 = The SPI transmits and receives the LSB (Least Significant Bit) first.

Bits 5:4

Comm Mode [1:0]

0 0: All SPI communication disabled.

0 1: SPI master mode

1 0: SPI slave mode

1 1: Reserved

Bit 3

CPOL

This bit controls the SPI clock (SCLK) idle polarity.

0 = SCLK idles low

1 = SCLK idles high

Bit 2

CPHA

The Clock Phase bit controls the phase of the clock on which data is sampled. Table 19-16 on page 46 shows the

timing for the various combinations of LSB First, CPOL, and CPHA.

Bits 1:0

SCLK Select

This field selects the speed of the master SCLK. When in master mode, SCLK is generated by dividing the base

CPUCLK.

Important Note for Comm Modes 01b or 10b (SPI Master or SPI Slave):

When configured for SPI, (SPI Use = 1—Table 19-11 on page 42), the input/output direction of pins P1.3, P1.5, and P1.6 is set

automatically by the SPI logic. However, pin P1.4's input/output direction is NOT automatically set; it must be explicitly set by

firmware. For SPI Master mode, pin P1.4 must be configured as an output; for SPI Slave mode, pin P1.4 must be configured as

an input.

[+] Feedback

CYWUSB6953 bảng dữ liệu(PDF) 45 Page - Cypress Semiconductor

CYWUSB6953 bảng dữ liệu(HTML) 45 Page - Cypress Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

bảng dữ liệu tải về

Link URL