NRF52810-QFAA-R7 datasheet(83/483 Pages) NORDIC

83 / 483 page

Power and clock management

Symbol

Description

Min.

Typ.

Max.

Units

tPOR,10ms

VDD rise time 10ms

tPOR,60ms

VDD rise time 60ms

tPINR

If a GPIO pin is configured as reset, the maximum time

taken to pull up the pin and release reset after power on

reset. Dependent on the pin capacitive load (C)10: t=5RC, R

= 13kOhm

tPINR,500nF

C = 500nF

32.5

tPINR,10uF

C = 10uF

650

tR2ON

Time from reset to ON (CPU execute)

tR2ON,NOTCONF

If reset pin not configured

tPOR

tR2ON,CONF

If reset pin configured

tPOR +

tPINR

tOFF2ON

Time from OFF to CPU execute

16.5

µs

tIDLE2CPU

Time from IDLE to CPU execute

3.0

µs

tEVTSET,CL1

Time from HW event to PPI event in Constant Latency

System ON mode

0.0625

µs

tEVTSET,CL0

Time from HW event to PPI event in Low Power System ON

mode

0.0625

µs

5.3.10.2 Power fail comparator

Symbol

Description

Min.

Typ.

Max.

Units

VPOF

Nominal power level warning thresholds (falling supply

voltage). Levels are configurable between Min. and Max. in

100mV increments.

1.7

2.8

VPOFTOL

Threshold voltage tolerance

±1

±5

VPOFHYST

Threshold voltage hysteresis

VBOR,OFF

Brown out reset voltage range SYSTEM OFF mode

1.2

1.7

VBOR,ON

Brown out reset voltage range SYSTEM ON mode

1.48

1.7

5.4 CLOCK — Clock control

The clock control system can source the system clocks from a range of internal or external high and low

frequency oscillators and distribute them to modules based upon a module’s individual requirements.

Clock distribution is automated and grouped independently by module to limit current consumption in

unused branches of the clock tree.

Listed here are the main features for CLOCK:

• 64 MHz on-chip oscillator

• 64 MHz crystal oscillator, using external 32 MHz crystal

• 32.768 kHz +/-500 ppm RC oscillator

• 32.768 kHz crystal oscillator, using external 32.768 kHz crystal

• 32.768 kHz oscillator synthesized from 64 MHz oscillator

• Firmware (FW) override control of oscillator activity for low latency start up

• Automatic oscillator and clock control, and distribution for ultra-low power

10 To decrease maximum time a device could hold in reset, a strong external pullup resistor can be

used.

4430_161 v1.0

NRF52810-QFAA-R7 bảng dữ liệu(PDF) 83 Page - Nordic Semiconductor

NRF52810-QFAA-R7 bảng dữ liệu(HTML) 83 Page - Nordic Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL