| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LM1770TMFX/NOPB bảng dữ liệu(PDF) 11 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
LM1770TMFX/NOPB bảng dữ liệu(HTML) 11 Page - Texas Instruments |
|
11 / 25 page ![]() L = (VIN ± VOUT) x D 0.3 x fSW x IOUT 'IL = (VIN ± VOUT) x D L x fSW VOUT + VDS_NMOS D = VIN + VDS_NMOS + VDS_PMOS VOUT D = VIN LM1770 www.ti.com SNVS403C – SEPTEMBER 2005 – REVISED APRIL 2013 DESIGN GUIDE The following section walks the designer through the steps necessary to select the external components to build a fully functional power supply. As with any DC-DC converter numerous trade-offs are possible to optimize the design for efficiency, size or performance. These will be taken into account and highlighted throughout this discussion. The first equation to calculate for any buck converter is duty-cycle. Ignoring conduction losses associated with the FETs and parasitic resistances it can be approximated by: (8) A more accurate calculation for duty-cycle can be used that takes into account the voltage drops across the FETs. Equation 9 can be used to determine the slight load dependency on switch frequency if needed. Otherwise the simplified equation works well for component calculation. (9) FREQUENCY SELECTION The LM1770 is available with three preset timing options that select the on-time and hence determine the switching frequency of the application. Increasing the switching frequency has the effect of reducing the inductor size needed for the application while requiring a slight trade-off in efficiency. Table 5 shows the same frequency table as shown previously in Table 3, with the exception that the recommended timing option for each VOUT is highlighted. It is not recommended to use a high switching frequency with VOUT equal to or greater than 2.5V due to the maximum duty-cycle limitations of the device coupled with the internal startup. Table 5. LM1770 Recommended VOUT Frequency Option VOUT Timing Options 500ns 1000ns 2000ns 0.8 485 242 - 1 606 303 - 1.2 727 364 - 1.5 909 455 227 1.8 - 545 273 2.5 - - 379 3.3 - - 500 INDUCTOR SELECTION The inductor selection is an iterative process likely requiring several passes before settling on a final value. The reason for this is because it influences the amount of ripple seen at the output, a critical component to ensure general stability of an adaptive on-time circuit. For the first pass at inductor selection the value can be obtained by targeting a maximum peak-to-peak ripple current equal to 30% of the maximum load current. The inductor current ripple ( ΔIL) can be calculated by: (10) Therefore, L can be initially set to the following by applying the 30% rule: (11) Copyright © 2005–2013, Texas Instruments Incorporated Submit Documentation Feedback 11 Product Folder Links: LM1770 |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |