S29GL01GS10DFIV13 datasheet(72/108 Pages) CYPRESS

72 / 108 page

Document Number: 001-98285 Rev. *R

Page 72 of 108

S29GL01GS/S29GL512S

S29GL256S/S29GL128S

10.5

DC Characteristics

Notes:

1. ICC active while Embedded Algorithm is in progress.

2. Not 100% tested.

3. Automatic sleep mode enables the lower power mode when addresses remain stable for the specified designated time.

4. VIO = 1.65V to VCC or 2.7V to VCC depending on the model.

5. VCC = 3V and VIO = 3V or 1.8V. When VIO is at 1.8V, I/O pins cannot operate at >1.8V.

6. During power-up there are spikes of current demand, the system needs to be able to supply this current to insure the part initializes correctly.

7. If an embedded operation is in progress at the start of reset, the current consumption will remain at the embedded operation specification until the embedded operation

is stopped by the reset. If no embedded operation is in progress when reset is started, or following the stopping of an embedded operation, ICC5 will be drawn during

the remainder of tRPH. After the end of tRPH the device will go to standby mode until the next read or write.

8. The recommended pull-up resistor for RY/BY# output is 5k to 10k Ohms.

Table 10.4 DC Characteristics (–40 °C to +85 °C)

Parameter

Description

Test Conditions

Min

Typ

(Note 2)

Max

Unit

ILI

Input Load Current

VIN = VSS to VCC, VCC = VCC max

–

+0.02

±1.0

µA

ILO

Output Leakage Current

VOUT = VSS to VCC, VCC = VCC max

–

+0.02

±1.0

µA

ICC1

VCC Active Read Current

CE# = VIL, OE# = VIH, Address

switching @ 5 MHz, VCC = VCC max

–55

ICC2

VCC Intra-Page Read Current

CE# = VIL, OE# = VIH, Address

switching @ 33 MHz, VCC = VCC max

–9

ICC3

VCC Active Erase/Program

Current (Notes 1, 2)

CE# = VIL, OE# = VIH, VCC = VCC max

–

100

ICC4

VCC Standby Current

CE#, RESET#, OE# = VIH, VIH = VIO

VIL = VSS, VCC = VCC max

–

100

µA

ICC5

VCC Reset Current (Notes 2, 7)

CE# = VIH, RESET# = VIL,

VCC = VCC max

–10

ICC6

Automatic Sleep Mode (Note 3)

VIH = VIO, VIL = VSS ,

VCC = VCC max, tACC + 30 ns

–3

VIH = VIO, VIL = VSS,

VCC = VCC max, tASSB

–

100

150

µA

ICC7

VCC Current during power up

(Notes 2, 6)

RESET# = VIO, CE# = VIO, OE# = VIO,

VCC = VCC max,

–53

VIL

Input Low Voltage (Note 4)

–0.5

–

0.3 × VIO

VIH

Input High Voltage (Note 4)

0.7 × VIO

–VIO + 0.4

VOL

Output Low Voltage (Notes 4, 8)

IOL = 100 µA for DQ15–DQ0;

IOL = 2 mA for RY/BY#

–

0.15 × VIO

VOH

Output High Voltage (Note 4)

IOH = 100 µA

0.85 × VIO

––

VLKO

Low VCC Lock-Out Voltage

(Note 2)

2.25

–

2.5

VRST

Low VCC Power on Reset

Voltage (Note 2)

–1.0

–

S29GL01GS10DFIV13 bảng dữ liệu(PDF) 72 Page - Cypress Semiconductor

S29GL01GS10DFIV13 bảng dữ liệu(HTML) 72 Page - Cypress Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL