| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
S29GL01GS10DFIV13 bảng dữ liệu(PDF) 70 Page - Cypress Semiconductor |
|
|
|||||||||||||||||||||||||||||
S29GL01GS10DFIV13 bảng dữ liệu(HTML) 70 Page - Cypress Semiconductor |
|
70 / 108 page ![]() Document Number: 001-98285 Rev. *R Page 70 of 108 S29GL01GS/S29GL512S S29GL256S/S29GL128S 10.4.2 Power Supply Voltages Operating ranges define those limits between which the functionality of the device is guaranteed. 10.4.3 Power-Up and Power-Down During power-up or power-down VCC must always be greater than or equal to VIO (VCC VIO). The device ignores all inputs until a time delay of tVCS has elapsed after the moment that VCC and VIO both rise above, and stay above, the minimum VCC and VIO thresholds. During tVCS the device is performing power on reset operations. During power-down or voltage drops below VCC Lockout maximum (VLKO), the VCC and VIO voltages must drop below VCC Reset (VRST) minimum for a period of tPD for the part to initialize correctly when VCC and VIO again rise to their operating ranges. See Figure 10.2 on page 71. If during a voltage drop the VCC stays above VLKO maximum the part will stay initialized and will work correctly when VCC is again above VCC minimum. If the part locks up from improper initialization, a hardware reset can be used to initialize the part correctly. Normal precautions must be taken for supply decoupling to stabilize the VCC and VIO power supplies. Each device in a system should have the VCC and VIO power supplies decoupled by a suitable capacitor close to the package connections (this capacitor is generally on the order of 0.1 µF). At no time should VIO be greater then 200 mV above VCC (VCC VIO –200 mV). Note: 1. Not 100% tested. Figure 10.1 Power-up VCC 2.7 V to 3.6 V VIO 1.65 V to VCC +200 mV Table 10.3 Power-Up/Power-Down Voltage and Timing Symbol Parameter Min Max Unit VCC VCC Power Supply 2.7 3.6 V VLKO VCC level below which re-initialization is required (Note 1) 2.25 2.5 V VRST VCC and VIO Low voltage needed to ensure initialization will occur (Note 1) 1.0 – V tVCS VCC and VIO minimum to first access (Note 1) 300 – µs tPD Duration of VCC VRST(min) (Note 1) 15 – µs Vcc (m a x) Vcc (m in ) Po w e r Su p p ly Vo lta g e tim e tVCS F u ll D e vice A cce ss Vcc V IO (m in) V IO (m a x) V IO |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |