| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
M42000004Z bảng dữ liệu(PDF) 14 Page - Advanced Micro Devices |
|
|
|||||||||||||||||||||||||||||
M42000004Z bảng dữ liệu(HTML) 14 Page - Advanced Micro Devices |
|
14 / 72 page ![]() November 1, 2002 Am42BDS640AG 13 P R E L I M INARY FLASH DEVICE BUS OPERATIONS Requirements for Asynchronous Read Operation (Non-Burst) To read data from the memory array, the system must first assert a valid address on A21–A0, while driving AVD# and CE# to V IL. WE# should remain at VIH. The rising edge of AVD# latches the address. The data will appear on DQ15–DQ0. Since the memory array is divided into four banks, each bank remains enabled for read access until the command register contents are altered. Address access time (t ACC) is equal to the delay from stable addresses to valid output data. The chip enable access time (t CE) is the delay from the stable addresses and stable CE# to valid data at the outputs. The output enable access time (t OE) is the delay from the falling edge of OE# to valid data at the output. The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious alteration of the memory content occurs during the power transition. Requirements for Synchronous (Burst) Read Operation The device is capable of continuous sequential burst operation and linear burst operation of a preset length. When the device first powers up, it is enabled for asyn- chronous read operation. Prior to entering burst mode, the system should deter- mine how many wait states are desired for the initial word (t IACC) of each burst access, what mode of burst operation is desired, which edge of the clock will be the active clock edge, and how the RDY signal will transi- tion with valid data. The system would then write the burst mode configuration register command sequence. See “Set Burst Mode Configuration Register Command Sequence” and “Flash Command Definitions” for further details. Once the system has written the “Set Burst Mode Con- figuration Register” command sequence, the device is enabled for synchronous reads only. The initial word is output t IACC after the active edge of the first CLK cycle. Subsequent words are output t BACC after the active edge of each successive clock cycle, which automatically increments the internal address counter. Note that the device has a fixed internal address boundary that occurs every 64 words, starting at address 00003Fh. During the time the device is out- putting data at this fixed internal address boundary (address 00003Fh, 00007Fh, 0000BFh, etc.), a two cycle latency occurs before data appears for the next address (address 000040h, 000080h, 0000C0h, etc.). The RDY output indicates this condition to the system by pulsing low. For standard handshaking devices, there is no two cycle latency between 3Fh and 40h (or multiple thereof). See Table 10. For reduced wait-state handshaking devices, if the address latched is 3Dh (or 64 multiple), an additional cycle latency occurs prior to the initial access. If the address latched is 3Eh (or 64 multiple) two additional cycle latency occurs prior to the initial access and the 2 cycle latency between 3Fh and 40h (or 64 multiple) will not occur. For 3Fh latched addresses (or 64 multiple) three additional cycle latency occurs prior to the initial access and the 2 cycle latency between 3Fh and 40h (or 64 multiple) will not occur. The device will continue to output sequential burst data, wrapping around to address 000000h after it reaches the highest addressable memory location, until the system drives CE# high, RESET# low, or AVD# low in conjunction with a new address. See Table 1, “Device Bus Operations,” on page 12. If the host system crosses the bank boundary while reading in burst mode, and the device is not program- ming or erasing, a two-cycle latency will occur as described above in the subsequent bank. If the host system crosses the bank boundary while the device is programming or erasing, the device will provide read status information. The clock will be ignored. After the host has completed status reads, or the device has completed the program or erase operation, the host can restart a burst operation using a new address and AVD# pulse. If the clock frequency is less than 6 MHz during a burst mode operation, additional latencies will occur. RDY indicates the length of the latency by pulsing low. 8-, 16-, and 32-Word Linear Burst with Wrap Around The remaining three modes are of the linear wrap around design, in which a fixed number of words are read from consecutive addresses. In each of these modes, the burst addresses read are determined by the group within which the starting address falls. The groups are sized according to the number of words read in a single burst sequence for a given mode (see Table 2.) Table 2. Burst Address Groups As an example: if the starting address in the 8-word mode is 39h, the address range to be read would be 38 - 3 F h , and t he bur st seq uence w ould be Mode Group Size Group Address Ranges 8-word 8 words 0-7h, 8-Fh, 10-17h, ... 16-word 16 words 0-Fh, 10-1Fh, 20-2Fh, ... 32-word 32 words 00-1Fh, 20-3Fh, 40-5Fh, ... |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |