| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TC1270AMAVRCTR bảng dữ liệu(PDF) 23 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
TC1270AMAVRCTR bảng dữ liệu(HTML) 23 Page - Microchip Technology |
|
23 / 42 page ![]() 2007-2022 Microchip Technology Inc. and its subsidiaries DS20002035F-page 23 TC1270A/70AN/71A 5.4 Modifying The Trip Point, VTRIP Although the TC127XA device has a fixed voltage trip point (VTRIP), it can be necessary to make custom adjustments. This is accomplished by connecting an external resistor divider to the TC127XA VDD pin. This causes the VSOURCE voltage to be higher than it is when the TC127XA input equals its VTRIP voltage (Figure 5-5). To maintain detector accuracy, the bleeder current through the divider should be significantly higher than the 15 µA maximum operating current required by the TC127XA. A reasonable value for this bleeder current is 1 mA (67 times the 10 µA required by the TC127XA). For example, if VTRIP = 2V and the desired trip point is 2.5V, the value of R1 + R2 is 2.5 k (2.5V/1 mA). The value of R1 + R2 can be rounded to the nearest standard value and plugged into the equation shown in Figure 5-5 to calculate values for R1 and R2. 1% tolerance resistors are recommended. FIGURE 5-5: Modifying Trip-Point using External Resistor Divider. 5.5 MOSFET Low-Drive Protection Low operating power and small physical size make the TC1270AN series ideal for many voltage detector applications. Figure 5-6 shows a low-voltage gate drive protection circuit that prevents the logic-level MOSFET from overheating due to insufficient gate voltage. When the input signal is below the threshold of the TC1270AN, its output grounds the gate of the MOSFET. FIGURE 5-6: MOSFET Low-Drive Protection. TC127XA VDD RST VSS R1 VSOURCE R2 or RST VSOURCE R1 R1 R2 + -------------------- VTRIP Where: Note: In this example, VSOURCE must be greater than VTRIP. VSOURCE = Voltage to be monitored VTRIP = Threshold Voltage setting VDD RST VSS TC1270AN 270 (1) MTP3055EL VDD RL VTRIP Note 1: This resistance should be sized appro- priately for the selected trip point volt- age related to the VOL operation. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |