| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
UPD6P9 bảng dữ liệu(PDF) 18 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
UPD6P9 bảng dữ liệu(HTML) 18 Page - Renesas Technology Corp |
|
18 / 73 page ![]() 16 µPD67, 67A, 68, 68A, 69 Data Sheet U14935EJ2V1DS 3.2.2 S0 port (bit 2 of P1) The S0 port is an input/OFF mode port. The pin state can be read by setting this port to input mode using bit 0 of the P4 register. In input mode, the use of a pull-down resistor for the S0 and S1/LED port can be specified in 2-bit units by software using bit 4 of the P4 register. If input mode is released (thus set to OFF mode), the pin becomes high-impedance but is configured so that through current does not flow internally. In OFF mode, 1 can be read regardless of the pin state. After reset, S0 is set to OFF mode, thus becoming high-impedance. 3.2.3 S1/LED port (bit 3 of P1) The S1/LED port is an I/O port. Input or output mode can be set using bit 2 of the P4 resister. The pin state can be read in both input mode and output mode. When in input mode, the use of a pull-down resistor for the S0 and S1/LED ports can be specified in 2-bit units by software using bit 4 of the P4 register. When in output mode, the pull-down resistor is automatically disconnected and this pin becomes the remote control transmission display pin (refer to 4 TIMER). After reset, S1/LED is placed in output mode, and a high level is output. 3.2.4 S2 port (bit 1 of P1) The S2 port is an input port. Use of STOP mode release for the S2 port can be specified by bit 3 of the P4 register. When using the pin as a key input from a key matrix, enable (bit 3 of the P4 register is set to 1) the use of STOP mode release (at this time, a pull-down resistor is connected internally.) When STOP mode release is disabled (bit 3 of the P4 register is set to 0), it can be used as an input port that does not release the STOP mode even if the release condition is met (at this time, a pull-down resistor is not connected internally.) The state of the pin can be read in both cases. After reset, S2 is set to input mode where the STOP mode release is disabled, and enters a high-impedance state. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |