JS28F320J3F75 datasheet(22/67 Pages) NUMONYX

22 / 67 page

Datasheet

Numonyx® Embedded Flash Memory (J3 65 nm) Single Bit per Cell (SBC)

6.0

Electrical Characteristics

6.1

DC Current Specifications

Table 7:

DC Current Characteristics

VCCQ

2.7 - 3.6V

Test Conditions

Notes

VCC

2.7 - 3.6V

Symbol

Parameter

Typ

Max

Unit

ILI

Input and VPEN Load Current

—

±1

μA

VCC = VCC Max; VCCQ = VCCQ Max

VIN = VCCQ or VSS

ILO

Output Leakage Current

—

±10

μA

VCC= VCC Max; VCCQ = VCCQ Max

VIN = VCCQ or VSS

ICCS

VCC Standby Current

120

μA

CMOS Inputs, VCC = VCC Max; Vccq =

VccqMax

Device is disabled (see

Table 17, “Chip

Enable Truth Table for 32-, 64-,

128-Mb” on page 30),

RP# = VCCQ ± 0.2 V

1,2,3

0.71

TTL Inputs, VCC = VCC Max,

Vccq = VccqMax

Device is disabled (see

Table 17, “Chip

Enable Truth Table for 32-, 64-,

128-Mb” on page 30), RP# = VIH

ICCD

VCC Power-Down Current

120

μARP# = VSS ± 0.2 V, IOUT (STS) = 0 mA

—

ICCR

8-Word Page

CMOS Inputs, VCC = VCC Max, VCCQ = VCCQ

Max using standard 8 word page mode

reads.

Device is enabled (see

Table 17, “Chip

Enable Truth Table for 32-, 64-,

128-Mb” on page 30)

f = 5 MHz, IOUT = 0 mA

1,3

CMOS Inputs,VCC = VCC Max, VCCQ = VCCQ

Max using standard 8 word page mode

reads.

Device is enabled (see

Table 17, “Chip

Enable Truth Table for 32-, 64-,

128-Mb” on page 30)

f = 33 MHz, IOUT = 0 mA

ICCW

VCC Program or Set Lock-Bit Current

CMOS Inputs, VPEN = VCC

1,4

TTL Inputs, VPEN = VCC

ICCE

ICCBC

VCC Block Erase or VCC Blank Check or

Clear Block Lock-Bits Current

CMOS Inputs, VPEN = VCC

1,4

TTL Inputs, VPEN = VCC

ICCWS

ICCES

VCC Program Suspend or Block Erase

Suspend Current

—10

Device is enabled (see

Table 17, “Chip

Enable Truth Table for 32-, 64-,

128-Mb” on page 30)

1,5

Notes:

All currents are in RMS unless otherwise noted. These currents are valid for all product versions (packages and speeds).

Contact Numonyx or your local sales office for information about typical specifications.

Includes STS.

CMOS inputs are either VCC ± 0.2 V or VSS ± 0.2 V. TTL inputs are either VIL or VIH.

Sampled, not 100% tested.

ICCWS and ICCES are specified with the device selected. If the device is read or written while in erase suspend mode, the

device’s current draw is ICCR and ICCWS.

JS28F320J3F75 bảng dữ liệu(PDF) 22 Page - Numonyx B.V

JS28F320J3F75 bảng dữ liệu(HTML) 22 Page - Numonyx B.V

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67

bảng dữ liệu tải về

Link URL