| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
STM32WB50CG bảng dữ liệu(PDF) 106 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32WB50CG bảng dữ liệu(HTML) 106 Page - STMicroelectronics |
|
106 / 119 page ![]() Electrical characteristics STM32WB50CG STM32WB30CE 106/119 DS13047 Rev 5 The I2C timings requirements are guaranteed by design when the I2C peripheral is properly configured (refer to the reference manual RM0471). The SDA and SCL I/O requirements are met with the following restriction: the SDA and SCL I/O pins are not “true” open-drain. When configured as open-drain, the PMOS connected between the I/O pin and VDD is disabled, but is still present. The 20 mA output drive requirement in Fast-mode Plus is supported partially. This limits the maximum load Cload supported in Fast-mode Plus, given by these formulas: tr(SDA/SCL) = 0.8473 x Rp x Cload Rp(min) = [VDD - VOL(max)] / IOL(max) where Rp is the I2C lines pull-up. Refer to Section 6.3.17 for the I2C I/Os characteristics. All I2C SDA and SCL I/Os embed an analog filter, refer to Table 81 for its characteristics. SPI characteristics Unless otherwise specified, the parameters given in Table 82 for SPI are derived from tests performed under the ambient temperature, fPCLKx frequency and supply voltage conditions summarized in Table 20: General operating conditions. Output speed is set to OSPEEDRy[1:0] = 11 Capacitive load C = 30 pF Measurement points are done at CMOS levels: 0.5 ₓ VDD Refer to Section 6.3.17 for more details on the input/output alternate function characteristics (NSS, SCK, MOSI, MISO for SPI). Table 80. Minimum I2CCLK frequency in all I2C modes Symbol Parameter Condition Min Unit f(I2CCLK) I2CCLK frequency Standard-mode - 2 MHz Fast-mode Analog filter ON, DNF = 0 9 Analog filter OFF, DNF = 1 9 Fast-mode Plus Analog filter ON, DNF = 0 19 Analog filter OFF, DNF = 1 16 Table 81. I2C analog filter characteristics(1) 1. Guaranteed by design. Symbol Parameter Min Max Unit tAF Maximum pulse width of spikes that are suppressed by the analog filter 50(2) 2. Spikes with widths below tAF(min) are filtered. 110(3) 3. Spikes with widths above tAF(max) are not filtered. ns |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |