| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
CS43L36 bảng dữ liệu(PDF) 46 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
CS43L36 bảng dữ liệu(HTML) 46 Page - Cirrus Logic |
|
46 / 89 page ![]() DS1081F3 46 CS43L36 4.10 Control-Port Operation For write operations, the bytes following the MAP byte are written to the CS43L36 register addresses pointed to by the last received MAP address, plus however many autoincrements have occurred. Note that, while writing, any autoincrementing block accesses that go past the maximum 0x7F address write to address 0x00—the page address. The writes then continue to the newly selected page. Fig. 4-27 shows a write pattern with autoincrementing. Figure 4-27. Control-Port Timing, I2C Writes with Autoincrement For read operations, the contents of the register pointed to by the last received MAP address, plus however many autoincrements have occurred, are output in the next byte. While reading, any autoincrementing block access that goes past the maximum 0x7F address wraps around and continues reading from the same page address. Fig. 4-28 shows a read pattern following the write pattern in Fig. 4-27. Notice how read addresses are based on the MAP byte from Fig. 4-27. Figure 4-28. Control-Port Timing, I2C Reads with Autoincrement To generate a read address not based on the last received MAP address, an aborted write operation can be used as a preamble (see Fig. 4-29). Here, a write operation is aborted (after the ACK for the MAP byte) by sending a Stop condition. 4 5 6 7 24 25 SCL CHIP ADDRESS(WRITE) MAP BYTE DATA DATA START STOP ACK ACK SDA 7 6 1 0 0 1 2 3 8 9 12 16 17 18 19 10 11 13 14 15 27 28 26 DATA SDA Source Master Master Master Pullup Slave Slave Slave Slave Master Pullup ACK ACK 7 6 5 4 3 2 1 0 MAP Addr = X 7 6 5 4 3 2 1 0 Master Master Slave 7 6 1 0 7 6 1 0 Addr = 10010 SCL SDA SDA Source Pullup DATA STOP ACK ACK 7 0 7 0 CHIP ADDRESS (READ) START 7 0 NO 25 8 9 18 4 5 6 7 0 1 2 3 16 17 34 35 36 ACK 7 6 5 4 3 2 1 0 DATA DATA Master Slave Slave Slave Master Master Master Pullup 27 Addr = 10010 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |