| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
RT3607CE bảng dữ liệu(PDF) 30 Page - Richtek Technology Corporation |
|
|
|||||||||||||||||||||||||||||
RT3607CE bảng dữ liệu(HTML) 30 Page - Richtek Technology Corporation |
|
30 / 69 page ![]() 30 RT3607CE www.richtek.com DS3607CE-01 June 2016 © Copyright 2016 Richtek Technology Corporation. All rights reserved. is a registered trademark of Richtek Technology Corporation. VREF R1 R2 80µA Function 1 Register Function 2 Register ADC Function 1 <5:0> Function 2 <5:0> R3 SETX (SETAX) VREF R1 R2 80µA Function 1 Register Function 2 Register ADC Function 1 <5:0> Function 2 <5:0> R3 SETX (SETAX) Figure 5. Multi-Function Pin Setting Mechanism with a R3 Resistor to Fine Tune the Set Voltage of Function2 VR Rail Addressing Setting The VR address of RT3607CE can be flipped by setting the voltage on SET3 with an external voltage divider as shown in Figure 6. The voltage at VREF pin will be pulled up to 3.2V after power ready (POR) and the voltage at VREF pin will fix to 0.6V within 500 μs after power ready (POR). Besides, when AXG rail address is set to 2, the boot voltage of AXG rail is 1.05V. Figure 6. VR Rail Addressing and Zero Load-Line Setting for SET3 VREF R1 R2 Function 1 Register ADC Function 1 <5:0> SET3 Anti-Overshoot and Anti-Overshoot Behavior The anti-overshoot function can be enabled or disabled by setting the voltage on SET3 with an external voltage divider. During the anti-overshoot function is triggered, the high side and low side MOS will both turn off. Therefore, the output voltage adds the forward voltage of the MOS parasitic body diode will crosses on the inductor to speed up the discharge speed and eases the overshoot magnitude. However, if the MOS driver has tri-state delay time, the performance of the anti-overshoot function will be degenerated. To prevent this phenomenon, RT3607CE provides two kinds of anti-overshoot low side MOS behavior. With the driver has tri-state delay time, the behavior of anti-overshoot can choose as high-low-floating, and with the driver without tri-state delay time, the behavior of anti- overshoot can choose as high-floating. High Switching Frequency Ramp The switching frequency of RT3607CE can support from 300kHz to 1.1MHz, however, with higher switching frequency, the ramp is needed to increase simultaneously to improve the system stability and smooth the mode transient performance. As switching is higher than 550k Hz, the high switching frequency ramp is suggested to be enabled. The high switching frequency ramp can be enabled or disabled by the internal current source 80 μA and the parallel of the high low side resistor on SET3 pin. Decrease GTU/SA Ramp Amplitude (Only Active in max phase = 1 Application) If RT3607CE apply in GTU or SA application and the maximum phase number is 1. The ramp amplitude will automatically increase to improve the stability. This function can be disabled to improve the transient performance by the internal current source 80 μA and the parallel of the high low side resistor on SET3 pin. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |