| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
RT3607CE bảng dữ liệu(PDF) 46 Page - Richtek Technology Corporation |
|
|
|||||||||||||||||||||||||||||
RT3607CE bảng dữ liệu(HTML) 46 Page - Richtek Technology Corporation |
|
46 / 69 page ![]() 46 RT3607CE www.richtek.com DS3607CE-01 June 2016 © Copyright 2016 Richtek Technology Corporation. All rights reserved. is a registered trademark of Richtek Technology Corporation. Current Monitor, IMON The RT3607CE includes a current monitor (IMON) function which can be used to detect over-current protection and the maximum processor current ICCMAX, and also sets a part of current gain in the load-line setting. It produces an analog voltage proportional to output current between the IMON and VREF pins. The calculation for IMON-VREF voltage is shown as below: IMON REF EQ L1 L2 L3 L4 CS DCR V V = R (I +I +I +I ) R where IL1+IL2+IL3+IL4 are output current and the definitions of DCR, RCS and REQ can refer to Figure 12. Over-Current Protection The RT3607CE provides Over-Current Protection (OCP) which is set by the SET1 pin. The OCP threshold setting can refer to ICCMAX current in Table 5. For example, if ICCMAX is set as 120A, users can set voltage by using the external voltage divider on the SET1 pin as 0.754V typically. If 156A OCP (130% x ICCMAX) threshold and DVID_TH (SR = 11.25mV/ μs) = 39.67mV / DVID_TH (SR = 33.75mV/ μs) = 119mV will be set. According to Table 6, the set voltage should be between 0.4755V and 0.4974V. When output current is higher than the OCP threshold, OCP is latched with a 40 μs delay to prevent false trigger. Besides, the OCP function is masked when dynamic VID transient occurs, and soft-start period. And the OCP function will re-active after 46 μs of DVID or soft- start alert is asserted. Output Over-Voltage Protection An OVP condition is detected when the VSEN pin is 350mV more than VID as VID > 1V. If VID < 1V, the OVP is detected when the VSEN pin is 350mV more than 1V. When OVP is detected, the high-side gate voltage UGATEx is pulled low and the low-side gate voltage LGATEx is pulled high. OVP is latched with a 0.5 μs delay- to prevent false trigger. Besides, the OVP function will be masked during DVID and soft-start period. After 46 μs of DVID or soft-start alert is asserted, the OVP function will re-active. Negative Voltage Protection Since the OVP latch continuously turns on all low-side MOSFETs of the VR, the VR will suffer negative output voltage. When the VSEN detects a voltage below −0.07V after triggering OVP, the VR triggers NVP to turn off all low-side MOSFETs of the VR while the high-side MOSFETs remain off. After triggering NVP, if the output voltage rises above 0V, the OVP latch restarts to turn on all low-side MOSFETs. Therefore, the output voltage may bounce between 0V and −0.07V due to OVP latch and NVP triggering. The NVP function will be active only after OVP is triggered. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |