| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PIC18F4331 bảng dữ liệu(PDF) 203 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC18F4331 bảng dữ liệu(HTML) 203 Page - Microchip Technology |
|
203 / 396 page ![]() 2003 Microchip Technology Inc. Preliminary DS39616B-page 201 PIC18F2331/2431/4331/4431 TABLE 17-3: EXAMPLE DEAD TIME RANGES 17.7.4 DEAD TIME DISTORTION 17.8 Independent PWM Output Independent PWM mode is used for driving the loads as shown in Figure 17-19 for driving one winding of a switched reluctance motor. A particular PWM output pair is configured in the Independent Output mode when the corresponding PMOD bit in the PWMCON0 register is set. No dead time control is implemented between the PWM I/O pins when the module is operat- ing in the Independent mode and both I/O pins are allowed to be active simultaneously. This mode can also be used to drive stepper motors. 17.8.1 DUTY CYCLE ASSIGNMENT IN THE INDEPENDENT MODE In the Independent mode, each duty cycle generator is connected to both PWM output pins in a given PWM output pair. The odd and the even PWM output pins are driven with a single PWM duty cycle generator. PWM1 and PWM0 are driven by the PWM channel which uses PDC0 register to set the duty cycle, PWM3 and PWM2 with PDC1, PWM5 and PWM4 with PDC2, PWM7 and PWM6 with PDC3, see Figure 17-3 and Register 17-3. Fosc (MHz) MIPS Prescaler Selection Dead Time Min Dead Time Max 40 10 FOSC/2 50 ns 3.2 µs 40 10 FOSC/4 100 ns 6.4 µs 40 10 FOSC/8 200 ns 12.8 µs 40 10 FOSC/16 400 ns 25.6 µs 32 8 FOSC/2 62.5 ns 4 µs 32 8 FOSC/4 125 ns 8 µs 32 8 FOSC/8 250 ns 16 µs 32 8 FOSC/16 500 ns 32 µs 25 6.25 FOSC/2 80 ns 5.12 vs 25 6.25 FOSC/4 160 ns 10.2 µs 25 6.25 FOSC/8 320 ns 20.5 µs 25 6.25 FOSC/16 640 ns 41 µs 20 5 FOSC/2 100 ns 6.4 µs 20 5 FOSC/4 200 ns 12.8 µs 20 5 FOSC/8 400 25.6 vs 20 5 FOSC/16 800 51.2 µs 10 2.5 FOSC/2 200 ns 12.8 µs 10 2.5 FOSC/4 400 ns 25.6 µs 10 2.5 FOSC/8 800 ns 51.2 µs 10 2.5 FOSC/16 1.6 µs 102.4 µs 51.25 FOSC/2 400 ns 25.6 µs 51.25 FOSC/4 800 ns 51.2 µs 51.25 FOSC/8 1.6 µs 102.4 µs 51.25 FOSC/16 3.2 µs 204.8 µs 41 FOSC/2 0.5 µs 32 µs 41 FOSC/4 1 µs 64 µs 41 FOSC/8 2 µs 128 µs 41 FOSC/16 4 µs 256 µs Note 1: For small PWM duty cycles, the ratio of dead time to the active PWM time may become large. In this case, the inserted dead time will introduce distortion into waveforms produced by the PWM mod- ule. The user can ensure that dead time distortion is minimized by keeping the PWM duty cycle at least three times larger than the dead time. A similar effect occurs for duty cycles at or near 100%. The maximum duty cycle used in the application should be chosen such that the minimum inactive time of the signal is at least three times larger than the dead time. If the dead time is greater or equal to the duty cycle of one of the PWM out- puts pairs, then that PWM pair will be inactive for the whole period. 2: Changing the dead time values in DTCON when the PWM is enabled may result in undesired situation. Disable the PWM (PTEN = 0) before changing the dead time value |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |