| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PIC18F4331 bảng dữ liệu(PDF) 202 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC18F4331 bảng dữ liệu(HTML) 202 Page - Microchip Technology |
|
202 / 396 page ![]() PIC18F2331/2431/4331/4431 DS39616B-page 200 Preliminary 2003 Microchip Technology Inc. REGISTER 17-5: DTCON – DEAD TIME CONTROL REGISTER 17.7.2 DEAD TIME RANGES The amount of dead time provided by the dead time unit is selected by specifying the input clock prescaler value and a 6-bit unsigned value defined in the DTCON register. Four input clock prescaler selections have been provided to allow a suitable range of dead times based on the device operating frequency. FOSC/2, FOSC/4, FOSC/8 and FOSC/16 are the clock prescaler options available using the DTPS1:DTPS0 control bits in the DTCON register. After selecting an appropriate prescaler value, the dead time is adjusted by loading a 6-bit unsigned value into DTCON<5:0>. The dead time unit prescaler is cleared on any of the following events: • On a load of the down timer due to a duty cycle comparison edge event; • On a write to the DTCON register; or • On any device Reset. 17.7.3 DECREMENTING THE DEAD TIME COUNTER The dead time counter is clocked from any of the Q clocks based on the following conditions. 1. The dead time counter is clocked on Q1 when: • The DTPS bits are set to any of the following dead time prescaler settings: Fosc/4, FOSC/8, FOSC/16 • The PWM Time Base Prescale bits (PTCKPS) are set to any of the following prescale ratios: FOSC/16, FOSC/64, FOSC/256. 2. The dead time counter is clocked by a pair of Q-clocks when the PWM Time Base Prescale bits are set to 1:1 (PTCKPS1:PTCKPS0 = 00, FOSC/4) and the dead time counter is clocked by the FOSC/2 (DTPS1:DTPS0 = 00). 3. The dead time counter is clocked using every other Q-clock depending on the two LSbs in the Duty Cycle registers: • If the PWM duty cycle match occurs on Q1 or Q3, then the dead time counter is clocked using every Q1 and Q3. • If the PWM duty cycles match occurs on Q2 or Q4, then the dead time counter is clocked using every Q2 and Q4. 4. When the DTPS1:DTPS0 bits are set to any of the other dead time prescaler settings, (i.e., FOSC/4, FOSC/8 or FOSC/16) and the PWM Time Base Prescaler is set to 1:1, the dead time counter is clocked by the Q-clock corresponding to the Q-clocks on which the PWM duty cycle match occurs. The actual dead time is calculated from the DTCON register as follows: Dead Time = Dead time value / (FOSC/prescaler) Table 17-3 shows example dead time ranges as a function of the input clock prescaler selected and the device operating frequency. R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 DTPS1 DTPS0 DT5 DT4 DT3 DT2 DT1 DT0 bit 7 bit 0 bit 7-6 DTPS1:DTPS0: Dead Time Unit A Prescale Select bits 11 = Clock source for Dead Time Unit is FOSC/16. 10 = Clock source for Dead Time Unit is FOSC/8. 01 = Clock source for Dead Time Unit is FOSC/4. 00 = Clock source for Dead Time Unit is FOSC/2. bit 5-0 DT5:DT0: Unsigned 6-bit dead time value bits for Dead Time Unit. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = bit is set ‘0’ = bit is cleared x = bit is unknown |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |