MB95F613K datasheet(81/110 Pages) CYPRESS

81 / 110 page

Document Number: 002-04698 Rev. *A

Page 81 of 110

PRELIMINARY

MB95610H Series

(Continued)

(VCC = 5.0 V10%, VSS = 0.0 V, TA = 40 C to 85 °C)

*1: • The power supply current is determined by the external clock. When the low-voltage detection reset circuit is selected, the power

supply current is the sum of adding the current consumption of the low-voltage detection reset circuit (ILVD) to one of the values

from ICC to ICCH. When both the low-voltage detection reset circuit and a CR oscillator are selected, the power supply current

is the sum of adding up the current consumption of the low-voltage detection reset circuit (ILVD), the current consumption of the

CR oscillator (ICRH or ICRL) and one of the values from ICC to ICCH. In on-chip debug mode, the main CR oscillator (ICRH) and

the low-voltage detection reset circuit are always in operation, and current consumption therefore increases accordingly.

• See “4. AC Characteristics (1) Clock Timing” for FCH, FCL, FCRH and FMCRPLL.

• See “4. AC Characteristics (2) Source Clock/Machine Clock” for FMP and FMPL.

• The power supply current value in standby mode is measured in deep standby mode. The current consumption in normal stand-

by is higher than that in deep standby mode. The power supply current value in normal standby can be found by adding the

current consumption difference between normal standby mode and deep standby mode (INSTBY) to the power supply current

value in deep standby mode. For details of normal standby and deep standby mode, refer to “CHAPTER 3 CLOCK CONTROL-

LER” in “New 8FX MB95610H Series Hardware Manual”.

*2: In sub-CR clock mode, the power supply current is the sum of adding ICCLS or ICCT to ICRH.

Parameter

Symbol

Pin name

Condition

Value

Unit

Remarks

Min

Typ

Max

LCD internal

division

resistance

RLCD

—

Between V4 and VSS

—20—



1/2 bias, 10 k

 resistor

—

200

—



1/2 bias, 100 k



resistor

—40—



1/4 bias, 10 k

 resistor

—

400

—



1/4 bias, 100 k



resistor

COM0 to COM7

output

impedance

RVCOM

COM0 to COM7

V1 to V4 = 4.1 V

——



SEG00 to

SEG51 output

impedance

RVSEG

SEG00 to SEG51

—



LCD leakage

current

ILCDL

V0 to V4, COM0 to

COM7, SEG00 to

SEG51

—

1—

1k

MB95F613K bảng dữ liệu(PDF) 81 Page - Cypress Semiconductor

MB95F613K bảng dữ liệu(HTML) 81 Page - Cypress Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL