MB95F613K datasheet(5/110 Pages) CYPRESS

5 / 110 page

Document Number: 002-04698 Rev. *A

Page 5 of 110

PRELIMINARY

MB95610H Series

(Continued)

Part number

Parameter

MB95F613H

MB95F614H

MB95F616H

MB95F613K

MB95F614K

MB95F616K

UART/SIO

2 channels

• Data transfer with UART/SIO is enabled.

• It has a full duplex double buffer, variable data length (5/6/7/8 bits), an internal baud rate generator and an error

detection function.

• It uses the NRZ type transfer format.

• LSB-first data transfer and MSB-first data transfer are available to use.

• Both clock asynchronous (UART) serial data transfer and clock synchronous (SIO) serial data transfer are enabled.

I2C bus

interface

1 channel

• Master/slave transmission and receiving

• It has the following functions: bus error function, arbitration function, transmission direction detection function,

wake-up function, and functions of generating and detecting repeated START conditions.

8/16-bit PPG

2 channels

• Each channel can be used as an “8-bit timer

 2 channels” or a “16-bit timer  1 channel”.

• The counter operating clock can be selected from eight clock sources.

16-bit reload timer

1 channel

• Two clock modes and two counter operating modes are available to use.

• It can output square wave.

• Count clock: it can be selected from internal clocks (seven types) and external clocks.

• Two counter operating modes: reload mode and one-shot mode

Event counter

By configuring the 16-bit reload timer and 8/16-bit composite timer ch. 1, the event count function can be

implemented. When the event counter function is used, the 16-bit reload timer and 8/16-bit composite timer ch. 1

become unavailable.

LCDC controller

(LCDC)

• COM output: 4 or 8 (max) (selectable)

• SEG output: 48 or 52 (max) (selectable)

- If the number of COM outputs is 4, the maximum number of SEG outputs is 52, and the maximum number of

pixels that can be displayed 208 (4

 52).

- If the number of COM outputs is 8, the maximum number of SEG outputs is 48, and the maximum number of

pixels that can be displayed 384 (8

 48).

• Duty LCD mode

• LCD standby mode

• Blinking function

• Internal divider resistor whose resistance value can be selected from 10 k

 or 100 k through software

• Interrupt in sync with the LCD module frame frequency

• Inverted display function

Watch counter

• Count clock: four selectable clock sources (125 ms, 250 ms, 500 ms or 1 s)

• The counter value can be selected from 0 to 63. (The watch counter can count for one minute when the clock

source is one second and the counter value is set to 60.)

Watch prescaler

Eight different time intervals can be selected.

MB95F613K bảng dữ liệu(PDF) 5 Page - Cypress Semiconductor

MB95F613K bảng dữ liệu(HTML) 5 Page - Cypress Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL