CS5530 datasheet(54/241 Pages) NSC

54 / 241 page

www.national.com

Revision 4.1

Functional Description (Continued)

3.4

POWER MANAGEMENT

The power management resources provided by a com-

bined CS5530/GXLV processor based system supports a

full-featured notebook implementation. The following

explanations pertain to a full-featured “notebook” power

management

system.

The

extent

which

these

resources are employed depends on the application and

on the discretion of the system designer.

Power management resources can be grouped according

to the function they enable or support. The major func-

tions are as follows:

• APM Support

• CPU Power Management

- Suspend Modulation

-3 Volt Suspend

-Save-to-Disk

• Peripheral Power Management

- Device Idle Timers and Traps

- General Purpose Timers

- ACPI Timer Register

- General Purpose I/O Pins

- Power Management SMI Status Reporting Registers

Included in the following subsections are details regarding

the registers used for configuring power management fea-

tures. The majority of these registers are directly

accessed through the PCI configuration register space

designated as Function 0 (F0). However, included in the

discussions are references to F1BAR+Memory Offset

xxh. This refers to the registers accessed through a base

address register in Function 1 (F1) at Index 10h (F1BAR).

F1BAR sets the base address for the SMI status and

ACPI timer support registers as shown in Table 3-11.

3.4.1

APM Support

Many notebook computers rely solely on an APM

(Advanced Power Management) driver for enabling the

operating system to power-manage the CPU. APM pro-

vides several services which enhance the system power

management and is theoretically the best approach; but in

its current form, APM is imperfect for the following rea-

sons:

• APM is an OS-specific driver, and may not be available

for some operating systems.

• Application support is inconsistent. Some applications

in foreground may prevent Idle calls.

• APM does not help with Suspend determination or

peripheral power management.

The CS5530 provides two entry points for APM support:

• Software CPU Suspend control via the CPU Suspend

Command Register (F0 Index AEh)

• Software SMI entry via the Software SMI Register (F0

Index D0h). This allows the APM BIOS to be part of the

SMI handler.

These registers are shown in Table 3-12.

Table 3-11. Base Address Register (F1BAR) for SMI Status and ACPI Timer Support

Bit

Description

F1 Index 10h-13h

Base Address Register - F1BAR (R/W)

Reset Value = 00000000h

This register sets the base address of the memory mapped SMI status and ACPI timer related registers. Bits [7:0] are read only (00h),

indicating a 256 byte memory address range. Refer to Table 4-16 for the SMI status and ACPI timer registers bit formats and reset val-

ues. The upper 16 bytes are always mapped to the ACPI timer, and are always memory mapped.

Note: In Silicon Revision 1.3 and above the ACPI Timer Count Register is accessible through I/O Port 121Ch.

31:8

SMI Status/Power Management Base Address

7:0

Address Range (Read Only)

CS5530 bảng dữ liệu(PDF) 54 Page - National Semiconductor (TI)

CS5530 bảng dữ liệu(HTML) 54 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL