TLE9263QX datasheet(19/164 Pages) INFINEON

19 / 164 page

TLE9263QX

General Product Characteristics

Data Sheet

Rev. 1.1, 2014-09-26

Note: There is no additional current consumption contribution due to PWM generators.

Current consumption for HSx

in SBC Stop Mode

Stop,HSx,85

–

575

700

µA

2)3)6)SBC Stop Mode;

j = 85°C;

Cyclic Sense & HSx =

ON (no load);

LIN, CAN,

WK1..3 = OFF

P_4.4.34

Current consumption for

cyclic sense function

Stop,CS25

–20

µA

3)7)8)SBC Stop Mode;

WD = OFF

P_4.4.23

Current consumption for

cyclic sense function

Stop,CS85

–24

µA

2)3)7)8)SBC Stop Mode;

j = 85°C;

WD = OFF

P_4.4.27

Current consumption for

watchdog active in Stop

Mode

Stop,WD25

–20

µA

2)SBC Stop Mode;

Watchdog running

P_4.4.30

Current consumption for

watchdog active in Stop

Mode

Stop,WD85

–24

µA

2)SBC Stop Mode;

j = 85°C;

Watchdog running

P_4.4.31

Current consumption for

active fail outputs (FO1..3)

Stop,FOx

–1.0

2.0

2)all SBC Modes;

j = 25°C; FOx = ON

(no load);

P_4.4.24

1) If the load current on VCC1 will exceed the configured VCC1 active peak threshold IVCC1,Ipeak1,r or IVCC1,Ipeak2,r,

the current consumption will increase by typ. 2.9mA to ensure optimum dynamic load behavior. Same applies to VCC2. For

VCC3 the current consumption will increase by typ. 1.4mA. See also Chapter 6, Chapter 7, Chapter 8.

2) Not subject to production test, specified by design.

3) Current consumption adders of features defined for SBC Sleep Mode also apply for SBC Stop Mode and vice versa (unless

otherwise specified).

4) No pull-up or pull-down configuration selected.

5) The specified WKx current consumption adder for wake capability applies regardless how many WK inputs are activated.

6) A typ. 75µA / max 125µA (

j = 85°C) adder applies for every additionally activated HSx switch in SBC Stop Mode;

In SBC Normal Mode every HSx switch consumes the typ. 75µA / max 125µA (

j = 85°C) without the initial adder because

the biasing is already enabled.

7) HS1 used for cyclic sense, Timer 2, 20ms period, 0.1ms on-time, no load on HS1.

In general the current consumption adder for cyclic sense in SBC Stop Mode can be calculated with below equation:

IStop,CS = 18µA + (525µA *tON/TPer)

8) Also applies to Cyclic Wake

Table 4

Current Consumption (cont’d)

Current consumption values are specified at Tj = 25°C, VS = 13.5V, all outputs open (unless otherwise specified)

Parameter

Symbol

Values

Unit

Note / Test Condition Number

Min.

Typ.

Max.

TLE9263QX bảng dữ liệu(PDF) 19 Page - Infineon Technologies AG

TLE9263QX bảng dữ liệu(HTML) 19 Page - Infineon Technologies AG

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL