ADC10D040CIVSSLASHNOPB datasheet(7/32 Pages) TI1

7 / 32 page

ADC10D040

www.ti.com

SNAS149G – OCT 2001 – REVISED MARCH 2013

Converter Electrical Characteristics (continued)

The following specifications apply for VA = VD = +3.3 VDC, VDR = +2.5 VDC, VREF = 1.4 VDC, GAIN = OF = 0V, OS = 3.3V, VIN

(a.c. coupled) = FSR = 1.4 VP-P, CL = 15 pF, fCLK = 40 MHz, 50% Duty Cycle, RS = 50Ω, trc = tfc < 4 ns, NOT offset corrected.

Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C

(1)

Units

Symbol

Parameter

Conditions

Typical(2)

Limits(3)

(Limits)

INTER-CHANNEL CHARACTERISTICS

1 MHz input to tested channel, 10.3 MHz input to

Crosstalk

−72

other channel

Channel - Channel Aperture Delay

fIN = 8 MHz

8.5

Match

Channel - Channel Gain Matching

0.1

%FS

REFERENCE AND ANALOG CHARACTERISTICS

Gain Pin = AGND

1.4

VP-P

VIN

Analog Differential Input Range

Gain Pin = VA

2.8

VP-P

Clock High

Analog Input Capacitance (each

CIN

input)

Clock Low

RIN

Analog Differential Input Resistance

13.5

Ω

0.6

V (min)

VREF

Reference Voltage

1.4

1.6

V (max)

IREF

Reference Input Current

µA

1.35

V (min)

VCMO

Common Mode Voltage Output

1 mA load to ground (sourcing current)

1.5

1.6

V (max)

Common Mode Voltage Temperature

ppm/°C

VCMO

Coefficient

DIGITAL INPUT CHARACTERISTICS

VIH

Logical “1” Input Voltage

VD = +3.0V

2.0

V (min)

VIL

Logical “0” Input Voltage

VD = +3.6V

0.5

V (max)

IIH

Logical “1” Input Current

VIH = VD

µA

IIL

Logical “0” Input Current

VIL = DGND

−1

µA

DIGITAL OUTPUT CHARACTERISTICS

VDR

VOH

Logical “1” Output Voltage

VDR = +2.5V, IOUT = −0.5 mA

V (min)

−0.2V

VOL

Logical “0” Output Voltage

VDR = +2.5V, IOUT = 1.6 mA

0.4

V (max)

Parallel Mode

−4.7

+ISC

Output Short Circuit Source Current

VOUT = 0V

Multiplexed Mode

−9

Parallel Mode

4.7

−ISC

Output Short Circuit Sink Current

VOUT = VDR

Multiplexed Mode

POWER SUPPLY CHARACTERISTICS

PD = LOW, STBY = LOW, d.c. input

mA (max)

Analog Supply Current

PD = LOW, STBY = HIGH

PD = HIGH, STBY = LOW or HIGH

0.1

PD = LOW, STBY = LOW, d.c. input

mA (max)

Digital Supply Current

PD = LOW, STBY = HIGH

0.1

PD = HIGH, STBY = LOW or HIGH

0.1

Digital Output Driver Supply

IDR

PD = STBY = LOW, dc input

1.9

2.5

mA (max)

Current(4)

(4)

IDR is the current consumed by the switching of the output drivers and is primarily determined by the load capacitance on the output

pins, the supply voltage, VDR, and the rate at which the outputs are switching (which is signal dependent). IDR = VDR (CO x fO + C1 x f1

+ ... + C9 x f9) where VDR is the output driver power supply voltage, Cn is the total capacitance on the output pin, and fn is the average

frequency at which that pin is toggling.

Submit Documentation Feedback

Product Folder Links: ADC10D040

ADC10D040CIVS/NOPB bảng dữ liệu(PDF) 7 Page - Texas Instruments

ADC10D040CIVS/NOPB bảng dữ liệu(HTML) 7 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

bảng dữ liệu tải về

Link URL